Exmark 0 Open the Fuel Shut-Off Valve, Starting the Engine, Engaging the PTO, Disengaging the PTO

Page 23

Operation

 

Figure 13

1. Engaged

2. Partially engaged — Do

 

Not operate with ROPS

 

in this condition.

Important: Always use the seat belt with the roll bar in the operate (raised) position. Ensure that the rear part of the seat is secured with the seat latch.

Open the Fuel Shut-Off Valve

Rotate the valve and align with the fuel line to open.

Starting the Engine

1.Move the motion control levers out to the neutral lock position.

2.Pull up and back on the parking brake lever to engage the parking brake.

3.Push down on the PTO switch to the “disengage” position.

Note: It is not necessary for the operator to be in the seat to start the engine.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.On a cold engine, push the choke lever forward into the “ON” position.

On a warm engine, leave the choke in the “OFF” position.

6.Turn ignition switch to the “START” position. Release the switch as soon as the engine starts.

Important: Do Not crank the engine continuously for more than ten seconds at a time. If the engine does not start, allow a 60 second cool-down period between starting

attempts. Failure to follow these guidelines can burn out the starter motor.

7.If the choke is in the “ON” position, gradually return choke to the “OFF” position as the engine warms up.

Engaging the PTO

DANGER

The rotating blades under the mower deck are dangerous. Blade contact can cause serious injury or kill you.

Do Not put hands or feet under the mower or mower deck when the blades are engaged.

DANGER

An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. Thrown objects or blade contact can cause serious injury or death.

Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly.

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

23

Image 23
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 Message Display Systems SpecificationsModel Numbers Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsTorque Requirements DimensionsProduct Overview Controls OperationFuel Gauge Ignition SwitchHour Meter Fuel Shut-Off ValveDeck Lift Pedal PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesRaise the Rollover Protection System Rops Pre-StartOperating Instructions Disengaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Engaging the PTODriving Forward Stopping the EngineDriving the Machine Driving in Reverse Adjusting the Cutting HeightAdjusting the Deck Lift Foot Pedal Adjusting the Anti-Scalp RollersDo Not drive a unit on a public street or roadway TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Tire Pressures Check Hydraulic Oil LevelChange Engine Oil Lubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings Change Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsStyle B yellow zinc Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Dielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Removing the Shim Electric Clutch AdjustmentShim Motion Control Linkage Adjustment Adjusting the height Motion Control Damper AdjustmentMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Full Forward Tracking AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z Advantage Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 28 pages 32.2 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 24 pages 21.56 Kb Manual 40 pages 46.04 Kb

0, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.