Exmark 0 Adjusting the Cutting Height, Adjusting the Deck Lift Foot Pedal, Driving in Reverse

Page 25

Operation

Driving in Reverse

1.Move the motion control levers inward to the neutral operate position.

2.To move rearward in a straight line, move both levers rearward with equal pressure.

To turn right, release pressure on the RH motion control lever and the rear of the machine will move towards the rear and to the right.

To turn left, release pressure on the LH motion control lever and the rear of the machine will move towards the rear and to the left.

3.To stop, position both motion control levers in the neutral operate position.

Adjusting the Cutting Height

The cutting height of the mower deck is adjusted from 1 1/2 to 4 1/2 inches (3.8 cm to 11.4 cm) in 1/4 inch (6.4 mm) increments.

1.Stop the machine and move the motion control levers outward to the neutral locked position.

2.Disengage the PTO.

3.Position the transport lock in the latching position.

4.Raise and lock the deck to the 4 1/2 inch (11.4 cm) transport position (Figure 16).

The deck is raised by pushing the foot operated deck lift pedal forward. The pedal is located at the front right corner of the floor pan.

Note: When changing the cutting height positions, always come to a complete stop and disengage the PTO.

5.Insert the height adjustment pin into the hole corresponding to the desired cutting height.

See the decal on the side of the deck lift plate for cut heights.

6.Push the deck lift pedal, release the transport lock and allow the deck to lower to the cutting height.

Adjusting the Deck Lift Foot Pedal

The deck lift foot pedal can be adjusted for operator comfort.

1.Stop the machine and move the motion control levers outward to the neutral locked position.

2.Disengage the PTO.

3.Engage the park brake.

4.Stop the engine, remove the key and wait for all moving parts to stop.

5.Position the transport lock in the latching position.

6.Raise and lock the deck to the 4 1/2 inch (11.4 cm) transport position (Figure 16).

7.Remove the two nuts from the deck lift foot pedal (see Figure 17).

Figure 17

1.

Deck lift foot pedal

4.

Hole set that moves

 

 

 

the pedal closer to the

 

 

 

operator

2.

Nuts

5.

Hole set that moves the

 

 

 

pedal away from the

 

 

 

operator

3.

Adjustment holes

6.

Adjusts the pedal higher

 

 

 

or lower

Figure 16

1.

Deck lift foot pedal

3.

Height of cut decal

2.

Height adjustment pin

4.

Transport lock control

 

 

 

 

8.Position the deck lift pedal for operator comfort and reinstall the nuts. Tighten hardware.

Adjusting the Anti-Scalp Rollers

It is recommended to change the anti-scalp roller position, when the height of cut has changed.

25

Image 25
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 Message Display Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsProduct Overview Controls OperationHour Meter Ignition SwitchFuel Shut-Off Valve Fuel GaugeLow Voltage Indicator PTO Engagement SwitchDrive Wheel Release Valves Deck Lift PedalOperating Instructions Pre-StartRaise the Rollover Protection System Rops Starting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTODriving the Machine Stopping the EngineDriving Forward Adjusting the Deck Lift Foot Pedal Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Driving in ReverseTransporting a Unit TransportingDo Not drive a unit on a public street or roadway Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeProposition 65 Warning Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs Lubricate Deck Lift Pivot Lubricate Brake Handle PivotCheck Spark Plugs Change Fuel FilterStyle a black finish Wheel Hub Slotted Nut Torque SpecificationStyle B yellow zinc Thread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling AdjustmentsPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Left Hand Brake Shown Removing the Shim Electric Clutch AdjustmentShim Motion Control Linkage Adjustment Motion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Motion Control Full Forward Tracking AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaClean Grass Build-Up Under Deck Remove Engine Shrouds and Clean Cooling FinsBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z Advantage Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 28 pages 32.2 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 24 pages 21.56 Kb Manual 40 pages 46.04 Kb

0, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.