Exmark 850 Motion Control Damper Adjustment, Motion Control Handle Adjustment, Adjusting the Tilt

Page 44

Maintenance

Motion Control Damper Adjustment

The top damper mounting bolt can be adjusted to obtain a more desired motion control lever resistance. See Figure 40 for mounting options.

2.Tighten or loosen the flanged nut to the desired feel.

For more resistance, tighten the flanged nut. For less resistance, loosen the flanged nut

3.Tighten jam nut.

Motion Control Handle

Adjustment

Adjusting the height:

The motion control levers can be adjusted higher or lower for maximum operator comfort.

1. Remove the two bolts holding the control lever to the control arm shaft (Figure 42).

Figure 40

RH Motion Control Shown

1. Torque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque. A T-40 Torx bit will be necessary to hold the stud from turning.

2. Most resistance (firmest feel)

3. Damper

4. Medium resistance (medium feel)

5. Least resistance (softest feel)

Motion Control Neutral Lock Pivot Adjustment

The flanged nut can be adjusted to obtain a more desired motion control lever resistance (Figure 41).

Figure 41

1. Flanged nut

2. Jam nut

1. Loosen the jam nut.

Figure 42

1.

Bolts

4.

Nuts

2.

Control lever

5.

Slotted holes

3.Control arm shaft

2.Move the control lever to the next set of holes. Secure the lever with the two bolts.

3.Repeat the adjustment for the opposite control lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for maximum operator comfort.

1.Loosen the upper bolt holding the control lever to the control arm shaft.

2.Loosen the lower bolt just enough to pivot the control lever fore or aft Figure 42. Tighten both bolts to secure the control in the new position.

3.Repeat the adjustment for the opposite control lever.

44

Image 44
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 Message Display Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Torque RequirementsProduct Overview Operation ControlsIgnition Switch Hour MeterFuel Shut-Off Valve Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Deck Lift PedalRaise the Rollover Protection System Rops Pre-StartOperating Instructions Open the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTODriving Forward Stopping the EngineDriving the Machine Adjusting the Cutting Height Adjusting the Deck Lift Foot PedalAdjusting the Anti-Scalp Rollers Driving in ReverseDo Not drive a unit on a public street or roadway TransportingTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Tire Pressures Check Hydraulic Oil LevelChange Engine Oil Lubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings Lubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterStyle B yellow zinc Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Check Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjustments Deck LevelingDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Electric Clutch Adjustment Removing the ShimShim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Handle AdjustmentMotion Control Neutral Lock Pivot Adjustment Adjusting the heightMotion Control Full Forward Tracking Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Clean Debris From MachineClean Grass Build-Up Under Deck Remove Engine Shrouds and Clean Cooling FinsBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Electrical DiagramSchematic ElectricalHydraulic Diagram Lazer Z Advantage Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 28 pages 32.2 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 24 pages 21.56 Kb Manual 40 pages 46.04 Kb

0, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.