Exmark 850 manual Electric Clutch Adjustment, Removing the Shim

Page 41

Maintenance

19. Install the rear tires and torque lug nuts to 90-95 ft-lb (122-129 N-m).

20. Remove jack stands.

Electric Clutch Adjustment

No adjustment necessary; however when the clutch brake has worn to the point where the clutch no longer engages consistently, the shim can be removed to extend the clutch life.

Figure 32

1. 2 inch height of cut location

E. Start the mower while in the operator position.

WARNING

Engine must be running and drive wheels must be turning so park brake adjustment can be performed. Contact with moving parts or hot surfaces may cause personal injury.

Keep fingers, hands, and clothing clear of rotating components and hot surfaces.

F.Release the park brake so the handle rests on the 1/2 x 6 inch rod or bolt.

G.Move the throttle to high idle.

H.Move both motion control levers to the full forward position and hold for 15 seconds.

I.Move both motion control levers to the full reverse position and hold for 15 seconds.

J.Turn off the engine and completely release the park brake by removing the 1/2 x 6 inch rod or bolt.

K.Allow the hubs to cool until they are cool enough to safely touch.

L.Rotate the drive wheel release handle to the “released” position. Refer to the Drive Wheel Release Valves section in Operation.

M.Readjust both brakes following the procedure in steps 10 through 14.

18.Rotate the drive wheel release handle to the “operating” position. Refer to the Drive Wheel Release Valves section in Operation.

Figure 33

1.

Armature

5.

Brake spacer

2.

Field shell

6.

Re-gap shim

3.

Rotor

7.

Brake pole

4.

Brake mounting bolt

 

 

Removing the Shim:

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. Allow the machine to cool completely before starting these instructions.

2.Using a pneumatic line, blow out any debris from under the brake pole and around the brake spacers.

41

Image 41
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 Message Display Systems SpecificationsModel Numbers Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsProduct Overview Controls OperationHour Meter Ignition SwitchFuel Shut-Off Valve Fuel GaugeLow Voltage Indicator PTO Engagement SwitchDrive Wheel Release Valves Deck Lift PedalRaise the Rollover Protection System Rops Pre-StartOperating Instructions Starting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTODriving Forward Stopping the EngineDriving the Machine Adjusting the Deck Lift Foot Pedal Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Driving in ReverseDo Not drive a unit on a public street or roadway TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Tire Pressures Check Hydraulic Oil LevelChange Engine Oil Lubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings Lubricate Deck Lift Pivot Lubricate Brake Handle PivotCheck Spark Plugs Change Fuel FilterStyle B yellow zinc Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Thread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling AdjustmentsDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Removing the Shim Electric Clutch AdjustmentShim Motion Control Linkage Adjustment Motion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Motion Control Full Forward Tracking AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaClean Grass Build-Up Under Deck Remove Engine Shrouds and Clean Cooling FinsBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z Advantage Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 28 pages 32.2 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 24 pages 21.56 Kb Manual 40 pages 46.04 Kb

0, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.