Exmark
4500-645
manual
Service Record, Date Description of Work Done Service Done By
Troubleshooting
Specs
Diagram
Safety Alert Symbol
Low Voltage Indicator
Dimension
Maintenance
Check Battery Charge
Adjusting the Cutting Height
Service Air Cleaner
Page 61
Service Record
Date:
Description of Work Done:
Service Done By:
61
Page 60
Page 62
Image 61
Page 60
Page 62
Contents
Lazer Z LPG Models
All Rights Reserved
Introduction
Contents
Safety Alert Symbol
Safety
Safe Operating Practices
Training
Do Not change the tanks when the engine is running
Inspection
With each tank change
Operation
Weekly
Tank Requalification
Slope Operation
Using the Rollover Protection System Rops
Maintenance and Storage
Safety
Safety and Instructional Decals
109-3148 109-7232
116-0157
116-0752
109-7069 109-9906
Model Numbers
Specifications
Systems
Hydrostatic Ground Drive System
Seat
Dimensions
Accessory Weight Table Worksheet
Curb Weight
Tread Width Center to Center of Tires, Widthwise
Wheel Base Center of Caster Tire to Center of Drive Tire
Torque Requirements
Product Overview
Controls
Operation
Motion Control Levers
Brake Lever
Safety Pressure Relief Valve
Ignition Switch
Hour Meter
Fuel Valve
Low Voltage Indicator
PTO Engagement Switch
LPG Cylinder Brackets
Drive Wheel Release Valves
Operating Instructions
Pre-Start
Raise the Rollover Protection System Rops
Starting the Engine
Open the Fuel Valve
Engaging the PTO
Disengaging the PTO
Driving Forward
Driving the Machine
Adjusting the Anti-Scalp Rollers
Adjusting the Cutting Height
Driving in Reverse
Transporting a Unit
Transporting
Do Not drive a unit on a public street or roadway
Loading a Unit
Operation
Recommended Maintenance Schedules
Maintenance
Check Engine Oil Level
Check Battery Charge
Proposition 65 Warning
Do Not jump start a weak battery if these conditions exist
Recommended Jump Starting Procedure
Check Mower Blades
Check Rollover Protections Systems Roll Bar Knobs
Check Safety Interlock System
Check Seat Belt
Service Air Cleaner
Check for Loose Hardware
Change Engine Oil
Check Condition Of Belts
Check Tire Pressures
Lubricate Grease Fittings
Lubricate Caster Wheel Hubs
Lubricate Deck Lift Pivot
Lubricate Brake Handle Pivot
Check Spark Plugs
Check LPG Tank
Change Hydraulic System Filter and Fluid
Change LPG Tank
Thread Locking Adhesives
Wheel Hub Slotted Nut Torque Specification
Copper-Based Anti-seize
Dielectric Grease
Deck Leveling
Adjustments
Pump Drive Belt Tension
Deck Belt Tension
Adjusting the Parking Brake
Electric Clutch Adjustment
Removing the Shim
Motion Control Linkage Adjustment
Motion Control Neutral Lock Pivot Adjustment
Motion Control Damper Adjustment
Motion Control Handle Adjustment
Adjusting the height
Adjusting the Tilt
Caster Pivot Bearings Pre-Load Adjustment
Remove Engine Shrouds and Clean Cooling Fins
Clean Engine and Exhaust System Area
Clean Hydro Fan Cooling Fins
Clean Debris From Machine
Waste Disposal
Battery Disposal
Motor Oil Disposal
Problem Possible Cause Corrective Action
Troubleshooting
See Drive Wheel Release Valves section
Troubleshooting
Diagram
Schematics
Electrical
Schematic
Hydraulic Diagram
General Warranty Conditions and Products Covered
Page
Date Description of Work Done Service Done By
Service Record
Page
This page may be copied for personal use
See EXMARK’S Complete Line of Accessories and Options
Related pages
All Service page
Prepare the Gun for Service for Graco PRO Xs4 AA
Customer Service for Haier ESAQ406P
LES Contenus ET Services DE Tiers Sont Fournis for Samsung GT-I9060MKAXEF
Lock Services for Sprint Nextel SCP-2400
Service Notes for Craftsman 917.376531
Associated Ports for the different System IP Services for Patton electronic 2635
HP DCE/9000 Core Services Software for HP UX DCE Software
Service for Apple Mac OS
What is the significance of the WTSAPI32 interface in NComputing X550?
(#)
Top
Page
Image
Contents