Exmark 4500-645 manual Seat, Hydrostatic Ground Drive System

Page 19

Specifications

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Parking Brake Release Button: Releases parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Pedal: Foot pedal that lifts deck.

Transport Lock:

Latching position: Automatically latches at the transport position.

Unlatching position: Deck does not latch at the transport position.

Seat

Type:

LZZ-LP Units: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, two-tone cover, armrests, integral safety switch, and seat vibration isolation system.

LZAS-LP Units: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, armrests, integral safety switch.

Optional seat accessories for units with standard seats:

Custom ride suspension system to enhance Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

Deluxe suspension seat with high back, low profile foam-in-place cushion (dampened, adjustable spring suspension), armrests, and integral safety switch. Seat height remains the same.

Seat Isolation System for reduced vibration, to enhance ride of standard seat, standard seat

with Custom Ride Seat Suspension or Deluxe Suspension Seat. Adds approximately 1 inch (2.5 cm) to seat height. Seat Isolation System is standard on all LZZ-LP units.

Mounting:

LZZ-LP Units: Hinged seat frame to tilt up seat. Held in tilted position with prop rod. Adjustable fore and aft on seat tracks.

LZAS-LP Units: Adjustable fore and aft on seat tracks.

Armrests:

Standard seat: foam padded adjustable flip-up armrests.

Suspension seat: molded adjustable flip-up armrests.

Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Two unitized hydrostatic transmissions:

LZZ-LP Units:

16cc Parker axial piston pump

280cc Ross geroler motor

LZAS-LP Units:

12cc Parker axial piston pump

240cc Parker geroler motor

Hydraulic Oil Type: Exmark Premium Hydro oil.

Hydraulic Oil Capacity: 52 oz (1.5 L) per side

Hydraulic Filter: P/N 116-0164

Speeds:

12cc

0-10 mph (16.1 km/hr) forward.

0-5.5 mph (8.9 km/hr) reverse.

16cc

0-11.5 mph (18.5 km/hr) forward.

0-6 mph (9.7 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

19

Image 19
Contents Lazer Z LPG Models All Rights Reserved Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesDo Not change the tanks when the engine is running Inspection Tank Requalification OperationWith each tank change WeeklySlope Operation Using the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 116-0157 116-0752 109-7069 109-9906 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatDimensions Wheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewBrake Lever OperationControls Motion Control LeversFuel Valve Ignition SwitchSafety Pressure Relief Valve Hour MeterDrive Wheel Release Valves PTO Engagement SwitchLow Voltage Indicator LPG Cylinder BracketsOperating Instructions Pre-StartRaise the Rollover Protection System Rops Disengaging the PTO Open the Fuel ValveStarting the Engine Engaging the PTODriving Forward Driving the MachineAdjusting the Anti-Scalp Rollers Adjusting the Cutting HeightDriving in Reverse Transporting a Unit TransportingDo Not drive a unit on a public street or roadway Loading a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeProposition 65 Warning Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemChange Engine Oil Service Air CleanerCheck Seat Belt Check for Loose HardwareLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsCheck LPG Tank Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsChange Hydraulic System Filter and Fluid Change LPG TankDielectric Grease Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsPump Drive Belt Tension Deck Belt Tension Adjusting the Parking BrakeElectric Clutch Adjustment Removing the Shim Motion Control Linkage Adjustment Adjusting the height Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentAdjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsWaste Disposal Battery DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram SchematicsElectrical SchematicHydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options