Exmark TT23KAEP manual Drive Lever Linkage Adjustment, Tracking Adjustment

Page 31

Maintenance

2.Loosen the front nut on left hydro control link as shown in Figure 15. Turn the rear control linkage adjusting nut counterclockwise until wheel rotates forward. Turn the rear nut of left control link clockwise 1/4 of a turn at a time, stopping to move the speed control forward and back to neutral, until left wheel stops rotating forward. Turn the nut an additional 1/2 turn and tighten the front jam nut making sure not to put a bind on the linkage. Make sure flat part of linkage is perpendicular to pin part of swivel. See Figure 15.

Figure 15

1.

Left Hydro Control Link

4.

Linkage is perpendicular

 

(left side shown)

 

to pin (correct position)

2.

Front nut

5.

Linkage in incorrect

3.

Rear nut

 

position

6.

End view of swivel

After adjusting the left hydro control linkage, move the speed control lever to the mid-speed position and then back to the neutral position. Recheck the left drive wheel rotation to see if further adjustment is necessary - be sure the speed control lever is in the neutral position.

Important: If inconsistent neutral occurs, check to be sure both springs are properly tightened on the speed control lever under the console–especially the rear pivot spring.

3.Place the speed control lever in neutral. Adjust the right side linkage by turning the quick track knob counterclockwise until the tire begins to rotate forward. Begin to retighten the knob clockwise about 1/4 turn at a time, stopping to move the speed control forward and back to neutral. Recheck the drive wheel rotation to see if further adjustment is necessary.

4.The spring that keeps tension on the knob should normally not need adjustment. However, if adjustment is needed, adjust to where length of spring is about 1 inch (2.5 cm) between washers. Adjust spring length by turning nut at front of spring.

Drive Lever Linkage

Adjustment

1.With rear of machine still on jack stands and engine running at full throttle, move the speed control lever to the midway position. Move the respective drive lever upward until it reaches the neutral position and engage neutral lock latches see Figure 16. If the tire rotates in either direction, the length of the drive lever linkage will need to be adjusted.

Figure 16

2.Adjust the linkage length by releasing the drive lever and removing clevis pin and rotating the linkage in the lower swivel. Lengthen the linkage if the tire is turning in reverse and shorten the linkage if the tire is creeping forward. Rotate the linkage several turns if the tire is rotating fairly fast. But as the adjustment gets closer, adjust the linkage in 1/2 turn increments. Release and re-engage neutral lock latch checking that the tire stops. Continue these process until the tire is at a dead stop.

Replace the hairpin back into each clevis pin.

3.Make this adjustment for both sides.

Tracking Adjustment

1.Stop engine and wait for all moving parts to stop. Raise rear of machine, remove jack stands, and carefully lower machine to the ground.

2.Check the drive tire pressures and tire circumferences as stated in Check the Tire Pressures section in Maintenance.

3.Run the unit and observe the tracking on a level, smooth, hard surface such as concrete or asphalt.

4.If the unit tracks to one side or the other, turn the quick track knob. Turn the knob right to “steer” right, turn the knob left to “steer” left.

31

Image 31
Contents Turf Tracer California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 103-2432 103-4935 116-0404 Model Numbers SpecificationsSystems Dimensions Torque Requirements Product OverviewControls OperationPre-Start Operating Instructions Driving the Machine Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingRecommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Change Fuel Filter Remove Engine Shrouds and Clean Cooling FinsLubricate Caster Wheel Hubs Check Spark PlugsHydraulic System Air Purge Change Hydraulic System FilterFuel Tank Mounting Hardware Specifications Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Copper-Based Anti-seize Brake AdjustmentSpeed Control Linkage Neutral Safety Switch Adjustment Mobil HTS Grease Or Food-Grade Anti-seizeHydro Control Linkage Adjustment Neutral Control Linkages AdjustmentTracking Adjustment Drive Lever Linkage AdjustmentWaste Disposal Hydro Pump Spring Tension SettingElectric Clutch Adjustment Clean Grass Build-Up Under DeckBattery Disposal Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Exmark Commercial Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options