Panasonic CU-E15CKP5 Setting the Fan Speed, FAN Heating, Setting the Vertical Airflow Direction

■Setting the Fan Speed

•Press 4 to select:-

There are five stages of fan speed in addition to Auto Fan speed.

AUTO

FAN – Heating

When the temperature of the discharge air increases, the fan speed increases. Cooling ● Dry

Changes the fan speed to generate a cool breeze. The air starts to blow out approximately 40 seconds after the start of Cooling or Soft Dry.

■Setting the Vertical Airflow Direction.

•Press 5 to select:-

AUTO

AUTO	•	For COOL/DRY operation.
		Swing up/down automatically.
	•	For HEAT operation
AUTO
		When the discharge air temperature is
		low such as at the start of the heating
		operation, the air blows at horizontal
		level. As the temperature rises, the hot
		air blows in a downwards direction.

●Louver adjustment range

●Notes

•Do not adjust the vertical airflow direction louver downward during Cooling and Soft Dry. Drops of water may condense on the air outlet vent and drip down.

•Use the remote control to change the vertical airflow direction louver. Using your hands to adjust the direction may cause the louver to malfunction. If this happens, stop operation immediately and restart.

■Setting the Horizontal Airflow Direction.

• Press 6 to select:-

Horizontal	Indoor
	Unit
Airflow
Direction	Remote	AUTO
	Control

AUTO	•	For COOL/DRY operation.
		Louvers swing horizontally at a fixed
		speed.
	•	For HEAT operation
AUTO
		When air temperature is low, air is sent
		in . When temperature goes up,
		louver swing horizontally at a fixed
		speed.

●Use this air conditioner under the following conditions:

Unit in °C

●Notes

•If the unit is not going to be used for an extended period of time, turn off the main power supply. If it is left at the ON position, approximately 2.8 W of electricity will be used even if the indoor unit has been turned off with the remote control.

•If operation is stopped, then restart immediately, the unit will resume operation only after 3 minutes.

●Operation Details

COOL – Cooling Operation

•To set the room temperature at your preference cooling comfort.

AUTO – Automatic Operation

•Sense indoor temperature to select the optimum mode.

•Temperature is not displayed on the remote control during AUTO operation.

DRY – Soft Dry Operation

•Dehumidifies while maintaining the setting temperature. The Soft Dry Operation is recommended during the rainy season.

•If the room temperature exceeds the setting temperature, operation switches to Cooling.

•The fan speed is rather slow during Soft Dry Operation.

•The humidity may not decrease when the indoor temperature is lower than the setting temperature on the remote control.

ENGLISH

Cooling, Fan Soft Dry

About 30°

Heating	About 30°
	About 60°

•The adjustment range is different for each operation i.e. Heating, Cooling and Soft Dry. (Fig.at left)

•The angle indicated on the remote control is different from that on the indoor unit.

•The louver angle automatically changes to prevent condensation during Cooling and Soft Dry.

•When operation stops, the louver automatically closes.

DBT: Dry Bulb Temp	Indoor		Outdoor
WBT: Wet Bulb Temp	DBT	WBT	DBT	WBT
Maximum Temperature-Cooling	32	23	43	26
(Maximum Temperature-Heating)	(30)	(-)	(24)	(18)
Minimum Temperature-Cooling	16	11	16	11
(Minimum Temperature-Heating)	(2)	(-)	(-5)	(-6)

HEAT – Heating Operation

•To warm up the room temperature upon your preference setting temperature.

•Heat is obtained from outdoor air to warm up the room. When the outdoor ambient air temperature falls, the heating capacity of the unit might be reduced. We recommend that you use an additional heating device when the outdoor ambient air temperature is low.

FAN – FAN Operation

•Circulates air throughout the room.

•Purifies and deodorizes the air if the air purifying filter is used. Fan Operation is recommended during seasons in which neither Heating nor Cooling is used.

∗Five stages of adjustments can be made in this range.

6