Ferris Industries 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER Attaching a Trailer

Page 26

Operation

Operation

Proper Mulching

Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn. These tiny particles decompose rapidly into by-products your lawn can use. UNDER PROPER CONDITIONS, your mulching mower will virtually eliminate noticeable clippings on the lawn surface.

NOTE: When mulching under heavy cutting conditions, a rumbling sound may be present and is normal.

MULCHING REQUIRES EXCELLENT MOWING CONDITIONS

Mulching mowers cannot function properly if the grass is wet, or if the grass is simply to high to cut. Even more than normal mowing, mulching requires that the grass be dry and the the appropriate amount is cut.

Do not use the mower as a mulching mower during the first two or three mowings in the spring. The long grass blades, quick growth, and often wetter conditions are more suitable for broadcasting (side- discharging) or grass bagging operation.

ENGINE SPEED & GROUND SPEED FOR

BROADCASTING

Use full engine throttle matched with a slow ground speed so that clippings will be finely cut. Ground speed while mulching should be HALF of the speed that would be used when broadcasting (side discharging) under similar conditions. Since mulching requires more horsepower than broadcasting, using a slower ground speed is vitally important for proper mulching operation.

HOW MUCH GRASS TO MULCH

The best mulching action typically results from cutting only the top 1/2 inch to 3/4 inch of grass blade. This provides short clippings which decompose properly (much more quickly than longer clippings). The ideal cutting height will vary with climate, time of year, and quality of your lawn. We recommend that you experiment with both the cutting height and ground speed until you achieve the best cut. Start with a high cutting height and using progressively lower settings until you find a cutting height that is matched to your mowing conditions and preferences.

ATTACHING A TRAILER

The maximum weight of a towed trailer should be less than 200 lbs (91kg). Secure the trailer with a appropriately sized clevis pin (A, Figure 12) and clip

(B).

Excessive towed loads can cause loss of traction and loss of control on slopes. Reduce towed weight when operating on slopes. The surface being driven on greatly impacts traction and stability. Wet or slippery surfaces can greatly reduce traction and the ability to stop or turn. Carefully evaluate the surface conditions before operating the unit and trailer, and never operate on slopes greater than 10°. See SLOPE OPERATION and TOWED EQUIPMENT in the safety section of this manual for additional safety information.

A

B

Figure 12. Trailer Weight Recommendations

A.Clevis Pin

B.Clip

Figure 11. Mulching Action

24

www.ferrisindustries.com

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Briggs & Stratton Power Products Group, LLC Model Number DescriptionDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Children Slope OperationTowed Equipment RIDE-ON Units EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons AIR Cooled Models only Seat Adjustment LeverIgnition Switch Control FunctionsParking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlLiquid Cooled Models only Water Temperature Gauge Never allow passengers to ride on the unit General Operating SafetyChecks Before Starting Pushing the Rider by Hand Starting the EngineStopping the Rider Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease PivotsCleaning the Battery and Cables Liquid Cooled Models Battery MaintenanceCleaning the Battery and Cables Air Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat Speed Balancing Adjustment Neutral AdjustmentReturn Spring RETURN-TO-NEUTRAL AdjustmentParking Brake Adjustment Set CollarTo adjust the upper mounting position Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Deck Lift ROD Timing Inner Rod4 Locations Deck Leveling AdjustmentDeck Lift Spring Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Chassis DimensionsEngine TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.
Top Page Image Contents