Ferris Industries 5900713 IS2000ZKAV25/52 AUS/NZ, 25HP, 52 CUT ZERO-TURN RIDING MOWER Set Collar

Page 41

 

Troubleshooting, Adjustment & Service

RETURN-TO-NEUTRAL

 

ADJUSTMENT

 

To determine if it is necessary to adjust the neutral

 

return, perform the following steps.

A

1. Disengage the PTO, engage the parking brake

 

and turn off the engine.

 

2. Move the ground speed control levers into the

 

operating position, pull levers rearward and

B

release.

 

3. Move the ground speed control levers out towards

 

the neutral position. If the levers do not align with

 

the notches in the neutral lock plate, it is

Figure 33. Return to Neutral Adjustment

necessary to adjust the neutral return rod.

A. Return Spring

 

TO ADJUST:

B. Set Collar

 

1.Loosen the set collar (B, Figure 33) locked against the return spring (A).

2.Lock the ground speed control levers in neutral.

3.Tighten set collar against the return spring.

4.Pull lever rearward and release to check that the lever stops aligned with notch in the neutral lock plate.

It is important to note that after every adjustment of the neutral return spring, the lever must be returned to locked position to properly check the neutral position.

PARKING BRAKE ADJUSTMENT

1.Disengage the PTO, engage the parking brake, stop the engine and remove the ignition key.

2.Raise the seat plate.

3.Locate the brake spring (A, Figure 34).

4.With the parking brake engaged, measure the compressed spring length. The spring should be 1-15/16” - 2” (4,9 - 5,1 cm) when compressed.

5.If the spring is not within this range, release the parking brake and turn the adjustment nut (B) to compress or release the spring.

6.Engage the parking brake and remeasure the spring.

CAUTION

Do not adjust the spring to be shorter than

1-15/16” (4,9 cm) when compressed. This may damage the brake mechanism.

If this does not correct the braking problem, see your Ferris dealer.

B

A

Figure 34. Parking Brake Adjustment

A.Brake Spring

B.Adjustment Nut

Troubleshooting

39

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Model Number Description Briggs & Stratton Power Products Group, LLCDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Ignition Switch Seat Adjustment LeverAIR Cooled Models only Control FunctionsHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlLiquid Cooled Models only Water Temperature Gauge Never allow passengers to ride on the unit General Operating SafetyChecks Before Starting Pushing the Rider by Hand Starting the EngineStopping the Rider Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Grease LubricationOil PivotsCleaning the Battery and Cables Liquid Cooled Models Battery MaintenanceCleaning the Battery and Cables Air Cooled Models Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat Neutral Adjustment Speed Balancing AdjustmentParking Brake Adjustment RETURN-TO-NEUTRAL AdjustmentReturn Spring Set CollarTo adjust the upper mounting position Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Inner Rod Deck Lift ROD Timing4 Locations Deck Leveling AdjustmentDeck Lift Spring Hydraulic Pump Drive Belt Replacement Deck Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Engine DimensionsChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.
Top Page Image Contents