Ferris Industries 5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER manual

Page 43

Troubleshooting, Adjustment & Service

MOWING HEIGHT ADJUSTMENT

The cutting height adjustment pin (A, Figure 36) controls the mower cutting height. The cutting height is adjustable between 1-3/4” (4,4 cm) and 5” (12,7 cm) in 1/4” (0,64 cm) increments.

1.Depress the deck lift foot pedal (B) until it locks into the 5” (12,7 cm) position.

2.Place the cutting height adjustment pin in the desired cutting height.

3.Depress the deck lift foot pedal then push the lock lever (C) towards the right to release the lock.

4.Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin.

 

C

B

A

 

FOOT PEDAL ADJUSTMENT

The deck lift foot pedal can be adjusted to accommodate the operator’s height for optimal comfort.

To adjust pedal position:

1.Remove the foot pedal (A, Figure 37) from the pedal mount tab (B).

2.Remove the pedal mount hardware (C) and rotate the tab 180 degrees.

3.Reinstall the pedal mount hardware and tighten securely.

4.Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 37.

Figure 36. Mowing Height Adjustment

A.Cutting Height Adjustment Pin

B.Deck Lift Foot Pedal

C.Deck Lift Lock lever

B

AC

Figure 37. Foot Pedal Adjustment

A.Deck Lift Foot Pedal

B.Pedal Mount Tab

C.Pedal Mount Hardware

Troubleshooting

41

Image 43
Contents Model Number Description Briggs & Stratton Power Products Group, LLCDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Control Functions Seat Adjustment LeverIgnition Switch AIR Cooled Models onlyThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeLiquid Cooled Models only Water Temperature Gauge Checks Before Starting General Operating SafetyNever allow passengers to ride on the unit Stopping the Rider Starting the EnginePushing the Rider by Hand Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeTurning Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerKeep roll bar in the raised position and use seat belt Raise & Lower the Roll BARTo lower the roll bar To raise the roll barLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessBefore Every Spring Each 100 250 Fall Use Hours Safety ItemsRider Maintenance Engine MaintenanceChange OIL & Filter Check Tire PressuresChecking / Adding Fuel Fuel FilterChange Hydraulic OIL Filter Check Hydraulic OIL LevelChange Interval Every 250 Hours Filter Part Number Check Engine Coolant Level Change Engine Coolant Clean Radiator & ScreenPressurized System Pivots LubricationGrease OilCleaning the Battery and Cables Air Cooled Models Battery MaintenanceCleaning the Battery and Cables Liquid Cooled Models Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Suspension Seat Seat AdjustmentGround Speed Control Lever Adjustment Neutral Adjustment Speed Balancing AdjustmentSet Collar RETURN-TO-NEUTRAL AdjustmentParking Brake Adjustment Return SpringTo adjust the spring pre-load Suspension AdjustmentTo adjust the upper mounting position Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Inner Rod Deck Lift ROD TimingDeck Lift Spring Deck Leveling Adjustment4 Locations Hydraulic Pump Drive Belt Replacement Deck Mower Belt ReplacementJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesJump Starting Transmissions DimensionsEngine ChassisFerris Limited Warranty Tractor Belts and BladesMower Deck

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.