Ferris Industries 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER Control Functions

Page 16

Features & Controls

AIR COOLED MODELS ONLY

Controls

CONTROL FUNCTIONS

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.

Ground Speed Levers

These levers control the ground speed of the rider. The left lever controls the left rear drive wheel and the right lever controls the right rear drive wheel.

Moving a lever forward increases the FORWARD speed of the associated wheel, and pulling back on a lever increases the REVERSE speed.

Note: The further a lever is moved away from the neutral position the faster the drive wheel will turn.

See the Operating the Zero Turn Rider section for steering instructions.

Seat Adjustment Lever

The seat can be adjusted forward and back. Move the lever towards the left, position the seat as desired, and release the lever to lock the seat in position.

Ignition Switch

The ignition switch starts and stops the engine, it has three positions:

OFF

Stops the engine and shuts off the

 

electrical system.

RUN

Allows the engine to run and powers

 

the electrical system.

START

Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN position with the engine stopped–this drains the battery.

14

www.ferrisindustries.com

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Briggs & Stratton Power Products Group, LLC Model Number DescriptionDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Training OperationPreparation Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Seat Adjustment Lever Ignition SwitchAIR Cooled Models only Control FunctionsPTO Power Take Off Switch Hour Meter / Maintenance ReminderParking Brake Throttle ControlLiquid Cooled Models only Water Temperature Gauge Checks Before Starting General Operating SafetyNever allow passengers to ride on the unit Stopping the Rider Starting the EnginePushing the Rider by Hand Zero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In Place Executing an End-Of-Row Zero TurnExecuting Turns TurningMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingRaise & Lower the Roll BAR To lower the roll barTo raise the roll bar Keep roll bar in the raised position and use seat beltStorage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysSafety Items Rider MaintenanceEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursCheck Tire Pressures Checking / Adding FuelFuel Filter Change OIL & FilterChange Hydraulic OIL Filter Check Hydraulic OIL LevelChange Interval Every 250 Hours Filter Part Number Check Engine Coolant Level Change Engine Coolant Clean Radiator & ScreenPressurized System Lubrication GreaseOil PivotsCleaning the Battery and Cables Air Cooled Models Battery MaintenanceCleaning the Battery and Cables Liquid Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSeat Adjustment Suspension Seat Seat AdjustmentGround Speed Control Lever Adjustment Speed Balancing Adjustment Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment Parking Brake AdjustmentReturn Spring Set CollarTo adjust the spring pre-load Suspension AdjustmentTo adjust the upper mounting position Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Deck Lift ROD Timing Inner RodDeck Lift Spring Deck Leveling Adjustment4 Locations Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckBattery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesJump Starting Dimensions EngineChassis TransmissionsFerris Limited Warranty Tractor Belts and BladesMower Deck

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.
Top Page Image Contents