Ferris Industries 5900629 IS2000ZLKAV2661, 26HP, 61 CUT ZERO-TURN RIDING MOWER Removing the Blade

Page 35

SERVICING THE MOWER BLADES

1.Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in the following steps.

2.To remove blade for sharpening, use a 1” wrench on the flats of the spindle shaft while removing the blade mounting bolt with a 15/16” wrench (Figure 25).

3.Use a file to sharpen blade to fine edge. Remove all nicks and dents in blade edge. If blade is severely damaged, it should be replaced.

4.Balance the blade as shown in Figure 26. Center the blade’s hole on a nail lubricated with a drop of oil. A balanced blade will remain level.

5.Reinstall each blade with the tabs pointing up toward deck as shown in Figure 27. Secure with a bolt and flat washer and torque bolts to 70 ft.lbs. (94 N.m.).

WARNING

Mower blades are sharp. For your personal safety, do not handle mower blades with bare hands. Careless or improper handling of blades may result in serious injury. For your personal safety, blade mounting bolts must each be installed with a flat washer then securely tightened. Torque blade mounting bolts to 70 ft.lbs. (94 N.m.)

Regular Maintenance

Figure 25. Removing the Blade

Nail

Figure 26. Balancing The Blade

Maintenance

Figure 27. Installing The Blade

A.Blade Bolt

B.Flat Washer

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Model Number Description Briggs & Stratton Power Products Group, LLCDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Emissions Slope OperationTowed Equipment RIDE-ON Units ChildrenIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Control Functions Seat Adjustment LeverIgnition Switch AIR Cooled Models onlyThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeLiquid Cooled Models only Water Temperature Gauge Never allow passengers to ride on the unit General Operating SafetyChecks Before Starting Pushing the Rider by Hand Starting the EngineStopping the Rider Reverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeTurning Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassProper Broadcast Mowing When and How Often to MowMowing Methods Mowing PatternsProper Mulching Attaching a TrailerKeep roll bar in the raised position and use seat belt Raise & Lower the Roll BARTo lower the roll bar To raise the roll barLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessBefore Every Spring Each 100 250 Fall Use Hours Safety ItemsRider Maintenance Engine MaintenanceChange OIL & Filter Check Tire PressuresChecking / Adding Fuel Fuel FilterChange Interval Every 250 Hours Filter Part Number Check Hydraulic OIL LevelChange Hydraulic OIL Filter Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Pivots LubricationGrease OilCleaning the Battery and Cables Liquid Cooled Models Battery MaintenanceCleaning the Battery and Cables Air Cooled Models Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat Neutral Adjustment Speed Balancing AdjustmentSet Collar RETURN-TO-NEUTRAL AdjustmentParking Brake Adjustment Return SpringTo adjust the upper mounting position Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Inner Rod Deck Lift ROD Timing4 Locations Deck Leveling AdjustmentDeck Lift Spring Hydraulic Pump Drive Belt Replacement Deck Mower Belt ReplacementJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Transmissions DimensionsEngine ChassisFerris Limited Warranty Mower Deck Belts and BladesTractor

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.
Top Page Image Contents