Ferris Industries 5900738 IS2000ZBV3061 CAL, 30HP, 61 CUT ZERO-TURN RIDING MOWER Deck Lift Spring

Page 45

Troubleshooting, Adjustment & Service

DECK LEVELING ADJUSTMENT

NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted.

1.Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 25 psi (1,72 bar).

2.Lock the deck lift pedal in the 5” (12,7cm) position. Place the deck height adjustment pin in the 4" position and lower deck the lift pedal until the arm contacts the pin.

3.Place 2 x 4 blocks under each corner of the mower deck with the 3-1/2” sides being vertical. Place a 1/4” (0,64cm) thick spacer on top of the rear 2 x 4 blocks. See Figure 41.

4.Adjust the front eyebolts until the chains are tight and the deck is still resting on the 2 x 4’s. Tighten jam nuts. See Figure 42.

5.Loosen the nuts and allow the rear of the deck to rest on the 2 x 4’s and 1/4” spacers. Slide the chains down in the slots until the chains are tight and tighten the nuts. See Figure 42.

6.Remove all 2 x 4 blocks and spacers from under the mower deck.

DECK LIFT SPRING

The deck lift springs (A, Figure 43) are factory set to provide optimal lifting performance.

Although it is fastened with a multi-position anchor, this is NOT AN ADJUSTMENT POINT.

DO NOT attempt to adjust the spring length or lifting performance will be compromised.

Figure 41.

2 x 4 Locations

Adjust

Here

Adjust

Here

Figure 42. Hanger Chain Adjustment

A

Troubleshooting

Figure 43. Deck Lift Spring Location A. Deck Lift Spring

43

Image 45
Contents Model Number Description Briggs & Stratton Power Products Group, LLCDate Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Identification NumbersSafety Decals Safety Interlock System North American Safety IconsOperational Safety Checks Ignition Switch Seat Adjustment LeverAIR Cooled Models only Control FunctionsHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlLiquid Cooled Models only Water Temperature Gauge General Operating Safety Checks Before StartingNever allow passengers to ride on the unit Starting the Engine Stopping the RiderPushing the Rider by Hand Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterCheck Hydraulic OIL Level Change Hydraulic OIL FilterChange Interval Every 250 Hours Filter Part Number Change Engine Coolant Clean Radiator & Screen Check Engine Coolant LevelPressurized System Grease LubricationOil PivotsBattery Maintenance Cleaning the Battery and Cables Air Cooled ModelsCleaning the Battery and Cables Liquid Cooled Models Removing the Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Seat Adjustment Suspension SeatGround Speed Control Lever Adjustment Neutral Adjustment Speed Balancing AdjustmentParking Brake Adjustment RETURN-TO-NEUTRAL AdjustmentReturn Spring Set CollarSuspension Adjustment To adjust the spring pre-loadTo adjust the upper mounting position Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Inner Rod Deck Lift ROD TimingDeck Leveling Adjustment Deck Lift Spring4 Locations Hydraulic Pump Drive Belt Replacement Deck Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Make Certain Vehicles do not TouchJump Starting Engine DimensionsChassis TransmissionsFerris Limited Warranty Belts and Blades TractorMower Deck

5900737 IS2000ZKAV2561 CAL, 25HP, 61 CUT ZERO-TURN RIDING MOWER, 5900750 IS2000ZKAV2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5901170 IS2000ZK2761, 27HP, 61 CUT ZERO-TURN RIDING MOWER, 5900624 IS2000ZKAV2552, 25HP, 52 CUT ZERO-TURN RIDING MOWER, 5900619 IS2000ZKAV2561, 25HP, 61 CUT ZERO-TURN RIDING MOWER specifications

Ferris Industries has long been recognized for its innovation in the lawn care industry, particularly with its range of high-performance zero-turn riding mowers. Among their standout models are the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and the IS2000ZK2752. Each of these models combines power, efficiency, and advanced technology, making them ideal choices for both residential and commercial lawn maintenance.

The IS2000ZKAV3461SS is powered by a robust 34HP engine, delivering exceptional torque and speed for demanding mowing tasks. Its 61-inch cutting deck allows for efficient mowing of large areas, significantly reducing mowing time. The mower features commercial-grade components, including heavy-duty frame construction and high-performance hydrology, ensuring reliability and durability over time.

In contrast, the IS2000ZBV30/61 AUS/NZ and IS2000ZBV3061 models are equipped with powerful 30HP engines. The 61-inch cut deck on both models enables a wide cutting path, making them perfect for extensive lawns and commercial properties. These mowers come with Ferris's patented Suspension System that enhances operator comfort by ensuring a smooth ride over uneven terrain while maintaining perfect ground contact for improved cutting performance.

The IS2000ZBV3061 CAL model also features a 30HP engine and a 61-inch cutting deck. Its design focuses on efficiency and productivity, making it suitable for commercial landscaping operations. The unit is equipped with smart technology that optimizes fuel efficiency while providing consistent power output, ensuring that the mower can handle tough jobs without consuming excessive fuel.

For those looking for a slightly smaller option, the IS2000ZK2752 offers a 27HP engine paired with a 52-inch cutting deck. This model is perfect for residential use or smaller commercial spaces, delivering excellent maneuverability without sacrificing performance. Its compact size allows for easy navigation around obstacles, making the mowing process quicker and more efficient.

All models from Ferris Industries include user-friendly controls, a comfortable seat for extended operation, and quick-release mechanisms for easy maintenance. With a focus on safety, these mowers come equipped with features like anti-scalp wheels and reverse mowing capabilities, ensuring a high-quality cut in various conditions.

In conclusion, Ferris Industries' lineup of zero-turn riding mowers, including the IS2000ZKAV3461SS, IS2000ZBV30/61 AUS/NZ, IS2000ZBV3061, IS2000ZBV3061 CAL, and IS2000ZK2752, exemplifies the perfect fusion of power, technology, and comfort. Whether for professional landscapers or homeowners with expansive lawns, these mowers offer exceptional performance and cutting-edge features designed to elevate the mowing experience.