Ferris Industries DDSKAV15CE, DDSKAV17CE, DDSKAV23CE Deck Leveling Adjustment, Ddsh Models only

Page 24

Troubleshooting, Adjustment & Service

DECK LEVELING ADJUSTMENT

(DDSH Models only)

1.Make sure there is one spacer above and below the frame on the front caster shafts and place hairpin clips in the 2” cutting height position (see Figure 17).

2.Rotate the blade on the RIGHT-HAND side (dis- charge side) until the tip faces the front of the machine.

3.Loosen the jam nuts (A, Figure 18) located on the front deck hanger shafts (B, Figure 18). Turn the right side shaft until a cutting height of 2” is obtained at the very tip of the blade towards the front of the machine.

B

A

Figure 17. Caster Spacers & Hairpin Clip

A.Caster Spacer

B.Hairpin Clip

B

A

4.Now place a straight edge on top of the cutter deck approximately 1” to the outside of the front deck mount on the right side and measure to the floor (see Figure 19). Record your measurement.

5.Repeat the measuring procedure listed in Step 4 for the left-hand side of the mower deck.

6.Compare the measurements taken in Step 4 & 5. If they differ by more than 1/16”, the front deck hanger shaft on the LEFT side (non-discharge side) must be adjusted.

7.Adjust the two front hanger shafts as needed until the tip of the blade is 2” from the floor and the meas- urements taken from the top of the deck to the floor are within 1/16" of each other.

8.Once the level of the deck has been adjusted, there should be no slack in the front hanger shafts. If one shaft moves, a shim (P/N 20928) is required.

Figure 18. Front Hanger Shaft Adjustment

A.Jam Nut

B.Front Hanger Shaft

Straight Edge

Measure Here

Figure 19. Mowing Height Measurement

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Powerheads Mower DecksDescription Ferris IndustriesFerris Limited Warranty FERRISFerris IndustriesTable of Contents Identification Numbers North American ModelsCE Models Training PreparationSafety Rules & Information OperationSlope Operation Do NotMaintenance and Storage ChildrenEmissions Safety Decals GeneralDash Panel Decal CE Compliance Specs Ignition Switch Control FunctionsForward Speed Control Lever / Reverse Speed Control Levers Features & Controls Safety Interlock SystemGeneral Operating Safety Checks Before StartingStarting the Engine Stopping the MowerDriving the Mower To make a left-hand turnOperating the Dual Drive Walk-Behind MowingPushing the Mower by Hand Storage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysCheck Tire Pressures See Before Every SpringFall Tire PressureRegular Maintenance Checking / Adding FuelFuel Filter Fuel Tank, Oil Reservoir & Fuel FilterLubrication Motion Control Pivot & Rod PivotBattery Maintenance Checking the Battery FluidCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting Adjustments & Service Troubleshooting the MowerTroubleshooting, Adjustment & Service Troubleshooting the Mower DeckMowing Height Adjustment Mount Blade Caster Height Of CutDeck Leveling Adjustment Ddsh Models onlyShim Assembly Position Shimming the Hanger ShaftsMower Belt Replacement and Adjustment PTO Clutch to Deck BeltSpindle Belt Mower PTO Belt Transmission Drive Belt Replacement Transmission Drive BeltTransmission Neutral & Tracking Adjustments Neutral AdjustmentTracking Adjustment If Machine Veers to the LeftTransmission Maintenance and Service Changing Oil & FiltersTo Bleed Air From Transmissions PTO Clutch Adjustment Blade Brake CheckBattery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryTroubleshooting, Adjustment & Service Engine BlockCommon Replacement Parts & Accessories Common Replacement PartsAccessories HOW and When to WATER, Fertilize & Aerate General InformationTypes of GRASS, Climate and Conditions Lawn Care & Mowing Information Tall Grass Requires Incremental CuttingInch Proper Cutting HeightWhen and HOW Often to MOW What Mowing Patterns to USEMowing Methods Proper Broadcast MowingProper Mulching How to start a healthy compost pile CompostingTips On Dealing With Clippings Methods actually contribute to a healthy lawnSolutions for Common Mowing Problems StreakingStepped Cutting Stepped CuttingUneven Cutting ScalpingStingers Common International Symbols Technical ManualsChoke LC-9

DDSKAV17CE, DDSKAV15CE, DDSKAV23CE specifications

Ferris Industries has long been a leader in the outdoor power equipment industry, known for delivering innovative and reliable solutions for landscaping and maintenance professionals. Among its impressive lineup, the Ferris DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE stand out as robust and efficient models designed to meet the demanding needs of lawn care and agricultural operations.

The DDSKAV23CE is equipped with a powerful 23 horsepower engine that enhances performance across various terrains. One of its main features is the advanced suspension system, which allows for superior handling and comfort during use. This model also incorporates a state-of-the-art hydrostatic drive system, providing smooth and precise acceleration, making it an ideal choice for operators who require high maneuverability and control on uneven grounds.

The DDSKAV15CE offers a compact yet powerful option, boasting a 15 horsepower engine. This model is particularly designed for smaller properties or residential use, where agility and ease of operation are paramount. Its lightweight design does not compromise durability, allowing users to traverse tight spots effortlessly. The DDSKAV15CE also incorporates ergonomic controls for reduced operator fatigue during extended use.

On the other hand, the DDSKAV17CE blends power and efficiency with its 17 horsepower engine. This model features a larger cutting deck, which increases productivity by allowing the user to cover more ground in less time. The DDSKAV17CE is also equipped with enhanced traction capabilities, ensuring it can handle wet or hilly terrains without losing performance.

All three models utilize Ferris's patented iCD Cutting System, which provides a superior quality of cut and maintains a consistent performance even in challenging mowing conditions. The cutting decks are designed for easy maintenance and longevity, ensuring your investment can endure the rigors of frequent use.

Moreover, each model is built with rugged aluminum frame construction that enhances durability while reducing overall weight, further improving maneuverability and reducing operator fatigue.

In summary, Ferris Industries' DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE models combine power, efficiency, and innovative technology, making them ideal solutions for landscaping professionals and property owners seeking reliable outdoor equipment. Their unique blend of features caters to varied landscape maintenance needs, ensuring they are equipped to handle the toughest tasks.
Top Page Image Contents