Ferris Industries DDSKAV23CE Transmission Neutral & Tracking Adjustments, Neutral Adjustment

Page 29

TRANSMISSION NEUTRAL & TRACKING ADJUSTMENTS

Neutral Adjustment

1.Park the machine on a smooth, level surface such as a concrete floor, away from bystanders and prefer- ably facing a wall. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Chock the front caster wheels. Raise the drive wheels off the ground and secure the machine with jack stands.

3.Start the engine and adjust throttle control to SLOW (lowest setting). See the STARTING THE ENGINE section for proper starting instructions.

4.Disengage the parking brake.

5.Using a 1/2” deep socket, SLOWLY turn the adjust- ment nut COUNTER-CLOCKWISE until the drive tire begins to rotate forward.

6.SLOWLY turn the adjustment nut CLOCKWISE until the drive tire begins to rotate backwards.

7.Set the adjustment half way in between where the forward and backwards rotations began.

8.Adjust the throttle control to FULL (highest setting). Cycle the speed control lever and neutral return pedal several times to insure and accurate adjust- ment has been made.

Troubleshooting, Adjustment & Service

B

A

Figure 29. Neutral & Tracking Adjustment Points

A.Left-Hand Adjustment

B.Right-Hand Adjustment

Tracking Adjustment

Before making a tracking adjustment, be sure to check the following:

•Drive tires are inflated to 15 psi (103 kPa).

•Caster tires are inflated to 25 psi (172 kPa), are greased and turn freely.

•All controls are free from damage and operate freely.

•Machine is at full operating temperature.

•Make sure the machine is in neutral when the foot pedal is depressed. If not, adjust neutral as described above.

If Machine Veers to the LEFT:

1.Turn the LEFT adjustment nut 1/8 - 1/4 turn

COUNTER-CLOCKWISE.

2.Turn the RIGHT adjustment nut 1/8 - 1/4 turn

CLOCKWISE.

3.Drive machine on a flat, level surface to test and repeat steps 1 & 2 as necessary.

If Machine Veers to the RIGHT:

1.Turn the RIGHT adjustment nut 1/8 - 1/4 turn

COUNTER-CLOCKWISE.

2.Turn the LEFT adjustment nut 1/8 - 1/4 turn

CLOCKWISE.

3.Drive machine on a flat, level surface to test and repeat steps 1 & 2 as necessary.

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Mower Decks PowerheadsDescription Ferris IndustriesFERRISFerris Industries Ferris Limited WarrantyTable of Contents CE Models Identification NumbersNorth American Models Preparation TrainingOperation Safety Rules & InformationSlope Operation Do NotEmissions Maintenance and StorageChildren Dash Panel Decal Safety DecalsGeneral CE Compliance Specs Forward Speed Control Lever / Reverse Speed Control Levers Ignition SwitchControl Functions Safety Interlock System Features & ControlsChecks Before Starting General Operating SafetyStopping the Mower Starting the EngineDriving the Mower To make a left-hand turnPushing the Mower by Hand Operating the Dual Drive Walk-BehindMowing Starting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysSee Before Every Spring Check Tire PressuresFall Tire PressureChecking / Adding Fuel Regular MaintenanceFuel Filter Fuel Tank, Oil Reservoir & Fuel FilterMotion Control Pivot & Rod Pivot LubricationCleaning the Battery and Cables Battery MaintenanceChecking the Battery Fluid Removing the Blade Servicing the Mower BladesTroubleshooting the Mower Troubleshooting Adjustments & ServiceTroubleshooting the Mower Deck Troubleshooting, Adjustment & ServiceMount Blade Caster Height Of Cut Mowing Height AdjustmentDdsh Models only Deck Leveling AdjustmentShimming the Hanger Shafts Shim Assembly PositionSpindle Belt Mower Belt Replacement and AdjustmentPTO Clutch to Deck Belt Mower PTO Belt Transmission Drive Belt Transmission Drive Belt ReplacementNeutral Adjustment Transmission Neutral & Tracking AdjustmentsTracking Adjustment If Machine Veers to the LeftTo Bleed Air From Transmissions Transmission Maintenance and ServiceChanging Oil & Filters Blade Brake Check PTO Clutch AdjustmentChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryEngine Block Troubleshooting, Adjustment & ServiceAccessories Common Replacement Parts & AccessoriesCommon Replacement Parts Types of GRASS, Climate and Conditions HOW and When to WATER, Fertilize & AerateGeneral Information Tall Grass Requires Incremental Cutting Lawn Care & Mowing InformationInch Proper Cutting HeightWhat Mowing Patterns to USE When and HOW Often to MOWProper Mulching Mowing MethodsProper Broadcast Mowing Composting How to start a healthy compost pileTips On Dealing With Clippings Methods actually contribute to a healthy lawnStreaking Solutions for Common Mowing ProblemsStepped Cutting Stepped CuttingStingers Uneven CuttingScalping Choke Common International SymbolsTechnical Manuals LC-9

DDSKAV17CE, DDSKAV15CE, DDSKAV23CE specifications

Ferris Industries has long been a leader in the outdoor power equipment industry, known for delivering innovative and reliable solutions for landscaping and maintenance professionals. Among its impressive lineup, the Ferris DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE stand out as robust and efficient models designed to meet the demanding needs of lawn care and agricultural operations.

The DDSKAV23CE is equipped with a powerful 23 horsepower engine that enhances performance across various terrains. One of its main features is the advanced suspension system, which allows for superior handling and comfort during use. This model also incorporates a state-of-the-art hydrostatic drive system, providing smooth and precise acceleration, making it an ideal choice for operators who require high maneuverability and control on uneven grounds.

The DDSKAV15CE offers a compact yet powerful option, boasting a 15 horsepower engine. This model is particularly designed for smaller properties or residential use, where agility and ease of operation are paramount. Its lightweight design does not compromise durability, allowing users to traverse tight spots effortlessly. The DDSKAV15CE also incorporates ergonomic controls for reduced operator fatigue during extended use.

On the other hand, the DDSKAV17CE blends power and efficiency with its 17 horsepower engine. This model features a larger cutting deck, which increases productivity by allowing the user to cover more ground in less time. The DDSKAV17CE is also equipped with enhanced traction capabilities, ensuring it can handle wet or hilly terrains without losing performance.

All three models utilize Ferris's patented iCD Cutting System, which provides a superior quality of cut and maintains a consistent performance even in challenging mowing conditions. The cutting decks are designed for easy maintenance and longevity, ensuring your investment can endure the rigors of frequent use.

Moreover, each model is built with rugged aluminum frame construction that enhances durability while reducing overall weight, further improving maneuverability and reducing operator fatigue.

In summary, Ferris Industries' DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE models combine power, efficiency, and innovative technology, making them ideal solutions for landscaping professionals and property owners seeking reliable outdoor equipment. Their unique blend of features caters to varied landscape maintenance needs, ensuring they are equipped to handle the toughest tasks.
Top Page Image Contents