Ferris Industries DDSKAV15CE manual Transmission Maintenance and Service, Changing Oil & Filters

Page 30

Troubleshooting, Adjustment & Service

TRANSMISSION MAINTENANCE AND SERVICE

The hydrostatic transmissions are sealed units that require no maintenance other than the following.

•Keep the grass screen and transmission cooling fins clear or grass, leaves and debris.

•Keep oil level in the reservoirs (A, Figure 30) at the “FULL” line (B, Figure 30). Extra oil in the reservoir will not benefit the machine.

•If it is necessary to add oil to the reservoirs, use SAE straight 20 or 30 weight motor oil. DO NOT use a multi-grade oils. Make sure the area around the oil reservoirs is free from dust, dirt and debris before opening the reservoirs.

•Make sure the oil reservoirs caps are tight.

•Keep water, dirt and debris from entering the oil reservoirs. A small amount of a contaminant could damage the transmissions.

B

C

Figure 30. Oil Reservoirs

A.Oil Reservoirs

B.“FULL” Line

Changing Oil & Filters

Make sure transmissions and imme- diate surrounding areas are free from dirt and debris before changing the oil and filters. Cleanliness while per- forming this operation is extremely important.

1.Park the machine on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Place a drain pan under each transmission and remove the filters to drain the oil. See Figure 31.

3.Once oil has drained from transmissions, replace with new filters (P/N 21068-1), placing a light film on the seal of the filter before installing. Hand-tighten filter only.

4.Fill oil reservoirs 3/4 full with SAE straight 20 or 30 weight motor oil.

To Bleed Air From Transmissions

1.Locate the machine in a secure area, away from bystanders and preferably facing a wall. Raise the drive tires off the ground and secure with jackstands.

2.Start the engine and adjust throttle control to FULL (highest setting). See the STARTING THE ENGINE section for proper starting instructions.

Figure 31. Transmission Oil Filter Location

(left-hand side shown)

3.Run engine for 15 minutes. Watch the oil level in the reservoirs. Add oil to the “FULL” line (B, Figure 30) as necessary.

4.Watch oil levels for the next few days and add oil to the reservoirs as necessary.

28

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Description PowerheadsMower Decks Ferris IndustriesFerris Limited Warranty FERRISFerris IndustriesTable of Contents Identification Numbers North American ModelsCE Models Training PreparationSlope Operation Safety Rules & InformationOperation Do NotMaintenance and Storage ChildrenEmissions Safety Decals GeneralDash Panel Decal CE Compliance Specs Ignition Switch Control FunctionsForward Speed Control Lever / Reverse Speed Control Levers Features & Controls Safety Interlock SystemGeneral Operating Safety Checks Before StartingDriving the Mower Starting the EngineStopping the Mower To make a left-hand turnOperating the Dual Drive Walk-Behind MowingPushing the Mower by Hand Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysFall Check Tire PressuresSee Before Every Spring Tire PressureFuel Filter Regular MaintenanceChecking / Adding Fuel Fuel Tank, Oil Reservoir & Fuel FilterLubrication Motion Control Pivot & Rod PivotBattery Maintenance Checking the Battery FluidCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeTroubleshooting Adjustments & Service Troubleshooting the MowerTroubleshooting, Adjustment & Service Troubleshooting the Mower DeckMowing Height Adjustment Mount Blade Caster Height Of CutDeck Leveling Adjustment Ddsh Models onlyShim Assembly Position Shimming the Hanger ShaftsMower Belt Replacement and Adjustment PTO Clutch to Deck BeltSpindle Belt Mower PTO Belt Transmission Drive Belt Replacement Transmission Drive BeltTracking Adjustment Transmission Neutral & Tracking AdjustmentsNeutral Adjustment If Machine Veers to the LeftTransmission Maintenance and Service Changing Oil & FiltersTo Bleed Air From Transmissions PTO Clutch Adjustment Blade Brake CheckCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryTroubleshooting, Adjustment & Service Engine BlockCommon Replacement Parts & Accessories Common Replacement PartsAccessories HOW and When to WATER, Fertilize & Aerate General InformationTypes of GRASS, Climate and Conditions Inch Lawn Care & Mowing InformationTall Grass Requires Incremental Cutting Proper Cutting HeightWhen and HOW Often to MOW What Mowing Patterns to USEMowing Methods Proper Broadcast MowingProper Mulching Tips On Dealing With Clippings How to start a healthy compost pileComposting Methods actually contribute to a healthy lawnStepped Cutting Solutions for Common Mowing ProblemsStreaking Stepped CuttingUneven Cutting ScalpingStingers Common International Symbols Technical ManualsChoke LC-9

DDSKAV17CE, DDSKAV15CE, DDSKAV23CE specifications

Ferris Industries has long been a leader in the outdoor power equipment industry, known for delivering innovative and reliable solutions for landscaping and maintenance professionals. Among its impressive lineup, the Ferris DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE stand out as robust and efficient models designed to meet the demanding needs of lawn care and agricultural operations.

The DDSKAV23CE is equipped with a powerful 23 horsepower engine that enhances performance across various terrains. One of its main features is the advanced suspension system, which allows for superior handling and comfort during use. This model also incorporates a state-of-the-art hydrostatic drive system, providing smooth and precise acceleration, making it an ideal choice for operators who require high maneuverability and control on uneven grounds.

The DDSKAV15CE offers a compact yet powerful option, boasting a 15 horsepower engine. This model is particularly designed for smaller properties or residential use, where agility and ease of operation are paramount. Its lightweight design does not compromise durability, allowing users to traverse tight spots effortlessly. The DDSKAV15CE also incorporates ergonomic controls for reduced operator fatigue during extended use.

On the other hand, the DDSKAV17CE blends power and efficiency with its 17 horsepower engine. This model features a larger cutting deck, which increases productivity by allowing the user to cover more ground in less time. The DDSKAV17CE is also equipped with enhanced traction capabilities, ensuring it can handle wet or hilly terrains without losing performance.

All three models utilize Ferris's patented iCD Cutting System, which provides a superior quality of cut and maintains a consistent performance even in challenging mowing conditions. The cutting decks are designed for easy maintenance and longevity, ensuring your investment can endure the rigors of frequent use.

Moreover, each model is built with rugged aluminum frame construction that enhances durability while reducing overall weight, further improving maneuverability and reducing operator fatigue.

In summary, Ferris Industries' DDSKAV23CE, DDSKAV15CE, and DDSKAV17CE models combine power, efficiency, and innovative technology, making them ideal solutions for landscaping professionals and property owners seeking reliable outdoor equipment. Their unique blend of features caters to varied landscape maintenance needs, ensuring they are equipped to handle the toughest tasks.
Top Page Image Contents