Hayter Mowers RT380H manual Removing the Cutter Deck, Sharpening the Blades, Installing the Blades

Page 36

3.Remove the bolt (5/8 inch wrench), curved washer, retainer, and blade (Figure 46). Use a block of wood as a wedge between the blade and the cutter deck to lock the blade when you are removing the bolt.

Figure 46

1.

Bolt

4.

Spindle

2.

Retainer

5.

Curved washer

3.Blade

4.Inspect all parts; replace any parts that are damaged.

Important: The curved part of the blade must be pointing toward the inside of the cutter deck to ensure proper cutting.

2.Tighten the blade bolt to 45 to 60 ft-lb (61 to 81 Nm).

Removing the Cutter Deck

1.Park the tractor on a level surface.

2.Disengage the blade control (PTO) and set the parking brake.

3.Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

4.Move the height-of-cut lever into the “D” notch.

5.Remove the height-of-cut lift assist spring from the retaining bolt (Figure 49). The spring is between the frame and the right rear wheel.

Sharpening the Blades

1.Use a file to sharpen the cutting edge at both ends of each blade (Figure 47). Maintain the original angle. The blade retains its balance if you remove the same amount of material from both cutting edges.

Figure 47

1.Sharpen at original angle

2.Check the balance of each blade by putting it on a blade balancer (Figure 48). If the blade stays in a horizontal position, the blade is balanced and can be used. If the blade is not balanced, file some metal off of the back side of the blade. Repeat this step until the blade is balanced.

Figure 48

1. Blade

2. Balancer

 

 

Installing the Blades

1.Install each blade, blade retainer, curved washer (cupped side toward blade), and the blade bolt (Figure 46).

 

 

Figure 49

1.

Spring

3. Spring tool

2.

Bolt

 

Note: Use the spring tool provided with the machine.

When you remove the cutter deck, the spring-tensioned height-of-cut lever could suddenly release and injure you or someone else.

Move the height-of-cut lever to the “D” position and remove the height-of-cut assist spring to release the spring tension.

6.Move the height-of-cut lever into the “A” notch.

7.Unhook the spring on the idler pulley arm from the bracket on the cutter deck (Figure 50).

36

Image 36
Contents RT380H Tractor With Recycling/Side Discharge DeckContents IntroductionSafety TrainingPreparation Operation Mow only in daylight or in good artificial lightSound Power Maintenance and StorageSound Pressure VibrationSlope Chart Safety and Instructional Decals 114-323693-6677 107-4922 Setup Loose PartsMedia and Additional Parts Installing the Front Wheels Installing the Steering WheelParts needed for this procedure No Parts Required ProcedureInstalling the Seat Activating the BatteryWait 5 to 10 minutes after filling the battery cells Checking the Engine Oil LevelInstalling the Anti-Scalp Wheels Checking the Safety Interlock SystemLubricating the Tractor Preparing the Cutter Deck Discharge ChuteChecking the Hydro Neutral Position Product Overview Checking the Traction Control PedalControls Using Stabilizer/Conditioner OperationPetrol and Oil Using the Parking Brake Positioning the SeatOperating the Headlights Setting the Height-of-Cut Engaging the Power Take Off PTOOperating the Blade Control PTO Starting the EngineUsing the Safety Interlock System Understanding the Safety Interlock SystemSetting the Tractor to Operate in Reverse Stopping the EngineTesting the Safety Interlock System Pushing the Tractor ManuallyTo Push the Tractor To Operate the TractorInstalling the Discharge Cover Driving Forward or BackwardStopping the Tractor Side Discharge or Mulch GrassOperating Tips Maintenance Recommended Maintenance SchedulesLubrication Engine Maintenance Greasing and Lubricating the TractorServicing the Engine Oil Servicing the Air Cleaner Changing the OilChanging the Oil Filter Removing the Foam and Paper ElementsInstalling the Foam and Paper Elements Cleaning the Foam and Paper ElementsServicing the Spark Plug Removing the Spark PlugFuel System Maintenance Installing the Spark PlugDraining the Fuel Tank Checking the Spark PlugElectrical System Maintenance Servicing the BatteryRemoving the Battery Replacing the Fuel FilterInstalling the Battery Adding Water to the BatteryChecking the Electrolyte Level Charging the Battery Servicing the FuseServicing the Headlights Removing the BulbDrive System Maintenance Installing the BulbServicing the Transaxle Fluid Checking the Fluid LevelCooling System Maintenance Cleaning the Cooling SystemBrake Maintenance Adjusting the Parking BrakeServicing the Parking Brake Checking the Parking BrakeBelt Maintenance Cutter Deck Maintenance Replacing the Blade Drive BeltServicing the Blades Installing the Blades Removing the Cutter DeckSharpening the Blades Idler spring Idler arm Eye-bolt Installing the Cutter Deck Leveling the Cutter Deck from Side-to-Side Adjusting the Front-to-Rear Blade Slope Cleaning Washing the Underside of the Cutter DeckStorage Cover the tractor to protect it and keep it clean Troubleshooting Problem Possible Cause Corrective ActionTractor does not drive Schematics Page Page 1st Year 12 months Page Limited Warranty Date of Sale Your Local Dealer