Husqvarna LZ6123LTKOA, 968999272 Mower Deck Leveling, Throttle Lever Tension, From rotating tires

Page 17

SETUP AND ADJUSTMENTS

Mower Deck Leveling

Loosen the nuts directly behind each ball joint on

Position machine on a flat surface. Preferably level

both rods that connect the pump arm to the mo-

concrete.

tion control assemblies. FIG - 5

Check the tire pressure in all four tires. Inflation

Start the engine. The park brake must be engaged

should be 15 psi.

and the motion control levers in the neutral slots

Place 2x4’s on edge under the cutting deck from

to start the engine. Run the engine approximately

half throttle

front to rear and lower the deck down onto 2x4’s.

 

Adjust the four lower chain bolts to the center slots

Release park brake to allow the wheels to rotate.

on the deck. FIG - 4 NOTE: Make sure the lift

Begin with either side and put the motion control

blocks under the frame are tightly bolted to the

lever into the neutral position.Adjust the motion con-

frame.

trol linkage by rotating the double nuts in the proper

 

Check the chains for equal tension. If unequal

direction until the wheel stops rotating. FIG - 5 Move

adjust lower chain bolt in slot.

the motion control lever forward then into the neutral

Place the deck in the 6” cutting height and mea-

position and place it into the neutral slot. The wheel

must be stopped completely at this point. Now do

sure from the cutting edge of the blade to the flat

the same in reverse and release the lever. The lever

level surface to check the deck cutting height.

should return to neutral on its own.

 

Motion

 

 

Control

Turn Here

 

Lever

Deck Lift Arm

To Adjust

 

Slots For Chain

 

 

Adjustment

 

Pump

 

 

Arm

FIG - 4

 

 

Throttle Lever Tension

 

 

Stop engine and remove key.

 

 

Throttle lever tension may be adjusted by tighten-

Loosen Here

Loosen Here

 

ing the pivot bolt. The pivot bolt secures the throttle

(Lt. Hand Thds.)

 

arm to the mounting bracket which is mounted to

 

 

the console. Access is gained by removing the

FIG - 5

 

console.

 

Run engine full throttle to make sure wheels do

Motion Control Linkage Adjustment

not rotate. Readjust if any rotation occurs.

This adjustment must be made with the rear

 

 

wheels rotating. Raise the rear of the machine

Repeat the whole process for the opposite side

and block it up so the wheels are free to rotate.

and tighten the nuts against the ball joints.

CAUTION: Keep hands, feet and clothing away

 

 

from rotating tires.

Turn machine off.

 

Tilt seat forward and remove the seat rod so the

 

 

 

seat may rotate forward onto the frame.

Reinstall the seat rod and check the wiring har-

 

Place a 2x4 board between the foot plate and the

ness to the seat safety switch for a good connec-

center of the seat to engage the seat safety switch.17

tion and return the seat to the normal position.

 

 

Image 17
Contents Manual no REV. IR 09/08/04 Operators manualHusqvarna. All rights reserved Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsGeneral Use Safety InstructionsSafety Instructions Keep children away from the work area Do as follows Driving on SlopesChildren Maintenance8011-563 Important Information TransportCustomer Responsibilities Roll Over Protection SystemPresentation PresentationTires Setup and AdjustmentsRops Assembly Roll Over Protection System Seat Install AdjustmentsControl Arms Engine OilMower Deck Leveling Motion Control Linkage AdjustmentThrottle Lever Tension From rotating tiresPark Brake Adjustment Operating instructions Operating InstructionsHour Meter Key SwitchPump Release Valves Fuel Shut OffSafety interlock system MaintenanceCutter Housings Mower bladesHydraulic system HardwareAir filter Lubrication Pump beltTire pressure Caster WheelsTorque Specifications Maintenance Schedule Problem Trouble ShootingPage Wiring Diagrams Wiring Diagrams

LZ5225TKAA, LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, LZ7227TKOA, LZ6123LTKOA, LZ6127TKOA, LZ7227TKOA specifications

Husqvarna has long been recognized as a leading manufacturer of innovative outdoor power equipment, and their line of zero-turn mowers exemplifies their commitment to quality and performance. Among their extensive offerings, models like the LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, and LZ7227TKOA stand out, catering to both residential and commercial users.

The LZ5225TKAA is designed for small to medium-sized lawns. It features a powerful engine that delivers a robust cutting performance while maintaining fuel efficiency. Its compact design allows for easy maneuverability in tight spaces, making it an ideal choice for homeowners who need to navigate around trees and flower beds. The mower's cutting deck is engineered for precision, providing an even cut across various grass types.

Moving up in the lineup, the LZ6123LTKOA and LZ6125TKAA offer enhanced features suitable for larger properties or professional landscapers. Both models come equipped with advanced cutting technology that ensures a clean and uniform finish. The LZ6125TKAA is particularly notable for its generous cutting width, which drastically reduces mowing time, maximizing productivity.

The LZ6127TKOA is designed for heavy-duty tasks, boasting a more powerful engine and larger cutting deck. This model is well-suited for commercial applications where performance and durability are paramount. It features a user-friendly control system that allows operators to adjust settings easily while on the move, enhancing the mowing experience.

For those who require the utmost in performance, the LZ7227TKOA is the top-of-the-line model. With an impressive combination of power, speed, and cutting efficiency, it is engineered for maximum output in challenging conditions. This model incorporates advanced vibration dampening technologies to minimize user fatigue, making it ideal for long working hours.

Each of these models is equipped with Husqvarna's proprietary technologies, including robust steel cutting decks and high-performance engines that are built to handle demanding tasks. Additionally, the mowers are compatible with a range of attachments, allowing for versatile year-round use.

In conclusion, the Husqvarna LZ series offers a variety of zero-turn mowers that combine cutting-edge technology, durability, and user-friendly features. Whether you are a homeowner or a professional landscaper, there is a Husqvarna model tailored to meet your specific mowing needs, ensuring a well-manicured lawn with every use.