Husqvarna 968999270, 968999272 Pump belt, Lubrication, Tire pressure, Caster Wheels, Fuel filter

Page 23

MAINTENANCE

Pump belt

Check belt every 100 hours for excessive wear. To replace belt. Relieve tension on the deck belt and remove deck belt from clutch. See deck belt instructions on previous page. Loosen bolt on the clutch tie down and rotate out of the way. Using a 1/2” drive ratchet inserted into the square hole in the pump idler arm relieve the tension on the pump belt and remove belt. To reinstall belt. Swing pump idler pulley out toward engine to route belt around it. Then route belt around right side pulley first as you are looking up from the underside of machine. Reinstall idler spring and use the ratchet to rotate idler so the belt may be installed all the way around the last pulley.

Lubrication

See service decal under foot plate for service points and maintenance intervals. Clean grease zerks thoroughly before greasing. See engine manual for engine service. FIG - 13

Tire pressure

Check every 25 hours. All four tires require 15 psi.

Caster Wheels

Check every 200 hours. Lift front of unit off of ground so caster wheels can rotate freely. Tighten caster bolt then back off 1/2 turn. Check that wheel rotates freely. If wheel does not rotate freely back

the caster bolt off in 1/4 turn increments until wheel rotates freely.

NOTE: DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures. Only use O.E.M. specified tires. Foam filled tires or solid tires will void the warranty

Fuel filter

Replace every 500 hours or annually. In extremely dirty conditions replacement may need to be at shorter intervals.

Winter storage

To prepare the machine for storage. Clean the machine, especially under the deck. Touch-up the paint or spray the underside of deck with a light coat of oil.

Inspect the machine for damage and loose hard- ware.

Change the oil.

Drain the fuel system or add stabilizer to fuel. Make sure to run the machine after to circulate stabi- lizer throughout system.

Remove the plugs and add 1 tablespoon of oil in each cylinder. Install plugs and crank the engine two or three revolutions.

Grease all zerks.

Remove battery and store inside and protect it from freezing temperatures.

SERVICE DECAL

FIG - 13

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Manual no REV. IR 09/08/04 Operators manualHusqvarna. All rights reserved Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsGeneral Use Safety InstructionsSafety Instructions Keep children away from the work area Do as follows Driving on SlopesChildren Maintenance8011-563 Important Information TransportCustomer Responsibilities Roll Over Protection SystemPresentation PresentationTires Setup and AdjustmentsRops Assembly Roll Over Protection System Engine Oil AdjustmentsSeat Install Control ArmsFrom rotating tires Motion Control Linkage AdjustmentMower Deck Leveling Throttle Lever TensionPark Brake Adjustment Operating instructions Operating InstructionsFuel Shut Off Key SwitchHour Meter Pump Release ValvesMower blades MaintenanceSafety interlock system Cutter HousingsHydraulic system HardwareAir filter Caster Wheels Pump beltLubrication Tire pressureTorque Specifications Maintenance Schedule Problem Trouble ShootingPage Wiring Diagrams Wiring Diagrams

LZ5225TKAA, LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, LZ7227TKOA, LZ6123LTKOA, LZ6127TKOA, LZ7227TKOA specifications

Husqvarna has long been recognized as a leading manufacturer of innovative outdoor power equipment, and their line of zero-turn mowers exemplifies their commitment to quality and performance. Among their extensive offerings, models like the LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, and LZ7227TKOA stand out, catering to both residential and commercial users.

The LZ5225TKAA is designed for small to medium-sized lawns. It features a powerful engine that delivers a robust cutting performance while maintaining fuel efficiency. Its compact design allows for easy maneuverability in tight spaces, making it an ideal choice for homeowners who need to navigate around trees and flower beds. The mower's cutting deck is engineered for precision, providing an even cut across various grass types.

Moving up in the lineup, the LZ6123LTKOA and LZ6125TKAA offer enhanced features suitable for larger properties or professional landscapers. Both models come equipped with advanced cutting technology that ensures a clean and uniform finish. The LZ6125TKAA is particularly notable for its generous cutting width, which drastically reduces mowing time, maximizing productivity.

The LZ6127TKOA is designed for heavy-duty tasks, boasting a more powerful engine and larger cutting deck. This model is well-suited for commercial applications where performance and durability are paramount. It features a user-friendly control system that allows operators to adjust settings easily while on the move, enhancing the mowing experience.

For those who require the utmost in performance, the LZ7227TKOA is the top-of-the-line model. With an impressive combination of power, speed, and cutting efficiency, it is engineered for maximum output in challenging conditions. This model incorporates advanced vibration dampening technologies to minimize user fatigue, making it ideal for long working hours.

Each of these models is equipped with Husqvarna's proprietary technologies, including robust steel cutting decks and high-performance engines that are built to handle demanding tasks. Additionally, the mowers are compatible with a range of attachments, allowing for versatile year-round use.

In conclusion, the Husqvarna LZ series offers a variety of zero-turn mowers that combine cutting-edge technology, durability, and user-friendly features. Whether you are a homeowner or a professional landscaper, there is a Husqvarna model tailored to meet your specific mowing needs, ensuring a well-manicured lawn with every use.
Top Page Image Contents