Husqvarna 968999269, 968999272, 968999271, 968999270 manual Hardware, Air filter, Hydraulic system

Page 22

MAINTENANCE

Hardware

Check daily. Inspect the entire machine for loose or missing hardware.

Air filter

See engine manufacturers specifications for cleaning and replacement intervals.

Hydraulic system

Check oil level in tank daily. Oil level should be 3/ 4” to 1” below the top of the tank. Check all fit- tings, hoses and lines for damage or leaks. Re- place or repair any questionable lines or fittings.

ONLY USE

Tri-Synthetic Formula

0

FIG - 11

Change the oil and filter after the first 250 hours of operation then annually after that. Drain tank and remove filter, be sure to clean around the tank and filter head before removal. Replace filter and drain plug and refill hydraulic tank. Only use MOBIL 1 synthetic oil. FIG - 11.

Raise and block up the rear of the machine so the drive wheels can rotate freely. Start the engine at the lowest RPM possible, move the motion con- trol levers forward and run machine for several minutes. Stop engine and recheck the oil level.

If the wheels do not respond an air lock has oc- curred within the system. The system must be bled off of air or let the machine set overnight to allow the air time to dissipate out of the oil. DO NOT run the machine with an air lock, serious damage can occur to the pumps and wheel mo- tors.

WARNING!

If a leak is suspected, use a piece of card- board or wood, NOT your hands. to check for leaks.

Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury.

If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immdediately.

Deck belt

Check every 75 to 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal op- eration.

To replace belt lower the deck to its lowest posi- tion. Remove the foot plate and belt shields. Use a ratchet with a 9/16” socket on the spring idler bolt to relieve the tension on the belt. Slide the belt off of pulley and fully remove the belt. Reverse the procedure for installation. See the decal on the top of deck for belt routing information. FIG - 12. After installation is complete check the belt for twists.

FIG - 12

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operators manual Manual no REV. IR 09/08/04Husqvarna. All rights reserved Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsSafety Instructions Safety InstructionsGeneral Use Keep children away from the work area Driving on Slopes Do as followsMaintenance Children8011-563 Transport Important InformationRoll Over Protection System Customer ResponsibilitiesPresentation PresentationRops Assembly Roll Over Protection System Setup and AdjustmentsTires Control Arms AdjustmentsSeat Install Engine OilThrottle Lever Tension Motion Control Linkage AdjustmentMower Deck Leveling From rotating tiresPark Brake Adjustment Operating Instructions Operating instructionsPump Release Valves Key SwitchHour Meter Fuel Shut OffCutter Housings MaintenanceSafety interlock system Mower bladesAir filter HardwareHydraulic system Tire pressure Pump beltLubrication Caster WheelsTorque Specifications Maintenance Schedule Trouble Shooting ProblemPage Wiring Diagrams Wiring Diagrams

LZ5225TKAA, LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, LZ7227TKOA, LZ6123LTKOA, LZ6127TKOA, LZ7227TKOA specifications

Husqvarna has long been recognized as a leading manufacturer of innovative outdoor power equipment, and their line of zero-turn mowers exemplifies their commitment to quality and performance. Among their extensive offerings, models like the LZ5225TKAA, LZ6123LTKOA, LZ6125TKAA, LZ6127TKOA, and LZ7227TKOA stand out, catering to both residential and commercial users.

The LZ5225TKAA is designed for small to medium-sized lawns. It features a powerful engine that delivers a robust cutting performance while maintaining fuel efficiency. Its compact design allows for easy maneuverability in tight spaces, making it an ideal choice for homeowners who need to navigate around trees and flower beds. The mower's cutting deck is engineered for precision, providing an even cut across various grass types.

Moving up in the lineup, the LZ6123LTKOA and LZ6125TKAA offer enhanced features suitable for larger properties or professional landscapers. Both models come equipped with advanced cutting technology that ensures a clean and uniform finish. The LZ6125TKAA is particularly notable for its generous cutting width, which drastically reduces mowing time, maximizing productivity.

The LZ6127TKOA is designed for heavy-duty tasks, boasting a more powerful engine and larger cutting deck. This model is well-suited for commercial applications where performance and durability are paramount. It features a user-friendly control system that allows operators to adjust settings easily while on the move, enhancing the mowing experience.

For those who require the utmost in performance, the LZ7227TKOA is the top-of-the-line model. With an impressive combination of power, speed, and cutting efficiency, it is engineered for maximum output in challenging conditions. This model incorporates advanced vibration dampening technologies to minimize user fatigue, making it ideal for long working hours.

Each of these models is equipped with Husqvarna's proprietary technologies, including robust steel cutting decks and high-performance engines that are built to handle demanding tasks. Additionally, the mowers are compatible with a range of attachments, allowing for versatile year-round use.

In conclusion, the Husqvarna LZ series offers a variety of zero-turn mowers that combine cutting-edge technology, durability, and user-friendly features. Whether you are a homeowner or a professional landscaper, there is a Husqvarna model tailored to meet your specific mowing needs, ensuring a well-manicured lawn with every use.
Top Page Image Contents