Husqvarna 532 42 20-50_R1, 96045000408 TO REPLACE MOWER BLADE DRIVE BELT See Fig, To Check Brake

Page 21
TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 26)

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 26)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

IDLER

PULLEYS

MANDREL

PULLEY

MANDREL

PULLEY

FIG. 26

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 27)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

5.Remove belt downward from engine pulley (E).

6.Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See “TO INSTALL MOWER” section in

this manual).

 

E

 

F

A

 

B

G

 

C

 

D TO CHECK BRAKE

02952

FIG. 27

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Owners Manual / 96045000408 YTH20K46Safe Operation Practices for Ride-On Mowers SAFETY RULESI. GENERAL OPERATION II. SLOPE OPERATIONV. SERVICE III. CHILDRENIV. TOWING TABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES TO CHECK BATTERY See Fig ASSEMBLYADJUST SEAT See Fig UNASSEMBLED PARTSCHECK DECK LEVELNESS CHECK TIRE PRESSURECHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEMOPERATION PH DG E KNOW YOUR TRACTORTO SET PARKING BRAKE See Fig HOW TO USE YOUR TRACTORSTOPPING See Fig. 5A TO USE THROTTLE CONTROL D See Fig. BTO ADJUST GAUGE WHEELS See Fig TO ADJUST MOWER CUTTING HEIGHT See FigTO MOVE FORWARD AND BACKWARD See Fig TO USE CRUISE CONTROL J See FigREVERSE OPERATION SYSTEM ROS See Fig TO OPERATE MOWER See FigTO OPERATE ON HILLS TO TRANSPORT See Figs. 3 andBEFORE STARTING THE ENGINE SERVICE REMINDER/HOUR METERCHECK ENGINE OIL LEVEL ADD GASOLINEPURGE TRANSMISSION MOWING TIPSLUBRICATION CHART MAINTENANCETRACTOR BATTERYBLADE CARE BLADE REMOVAL See FigV-BELTS ENGINETRANSAXLE COOLING TRANSAXLE PUMP FLUIDCLEAN AIR INTAKE/COOLING AREAS CLEANINGCLEAN AIR SCREEN AIR FILTERTO INSTALL MOWER See Figs SERVICE AND ADJUSTMENTSTO REMOVE MOWER See Fig Q R AEE FJ H TO LEVEL MOWER TO REPLACE MOWER BLADE DRIVE BELT See Fig TO CHECK BRAKETO REPLACE MOTION DRIVE BELT See Fig TO START ENGINE WITH A WEAK BATTERY See Fig TO ADJUST STEERING WHEEL ALIGNMENTFRONT WHEEL TOE-IN/CAMBER TO REMOVE WHEEL FOR REPAIRS See FigTO REMOVE HOOD AND GRILL ASSEMBLY See Fig REPLACING BATTERY See FigTO ADJUST THROTTLE CONTROL CABLE TO ADJUST CARBURETOROTHER STORAGEFUEL SYSTEM ENGINE OILPROBLEM TROUBLESHOOTING POINTSCAUSE CORRECTIONEngine dies when TRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 SCHEMATICIGNITION SWITCH SCH10With Service Minder Option ELECTRICALTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 T04SELECTRICAL CHASSIS CHASSIS drive-texT2pedal10 DRIVEDRIVE ENGINE SPARK ARRESTER KITengine-texKohl7 ENGINE steering-texLEGND216 STEERING ASSEMBLYTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 DECALS WHEELS AND TIRESwheelart1-tex seat-tex6.5SL3 SEAT ASSEMBLY46texltpred3r6 MOWER DECKMOWER DECK lift-tex6 MOWER LIFTHUSQVARNA PRODUCT REGISTRATION INFORMATION & WARRANTY STATEMENT SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY SECTION 2 HUSQVARNAS OBLIGATIONS UNDER THE WARRANTYSECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION SECTION 4 EXCEPTIONS AND LIMITATIONSPrinted in the U.S.A 532 42 20-50R1 07.30.08 AP
Top Page Image Contents