Husqvarna 532 42 20-50_R1 Transmission, REPLACING BATTERY See Fig, To Replace Headlight Bulb

Page 23
REPLACING BATTERY (See Fig. 30)

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

Lower seat pan.

SEAT PAN

02602

TERMINAL

 

NUT

COVER

 

 

BOLT

 

 

POSITIVE

 

NEGATIVE

(RED)

 

 

(BLACK)

CABLE

 

 

CABLE

 

02603

FIG. 30

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02778

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

TRANSMISSION

REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

23

Image 23
Contents Owners Manual / 96045000408 YTH20K46II. SLOPE OPERATION SAFETY RULESSafe Operation Practices for Ride-On Mowers I. GENERAL OPERATIONIV. TOWING V. SERVICEIII. CHILDREN CUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS UNASSEMBLED PARTS ASSEMBLYTO CHECK BATTERY See Fig ADJUST SEAT See FigCHECK BRAKE SYSTEM CHECK TIRE PRESSURECHECK DECK LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTSOPERATION PH DG E KNOW YOUR TRACTORTO USE THROTTLE CONTROL D See Fig. B HOW TO USE YOUR TRACTORTO SET PARKING BRAKE See Fig STOPPING See Fig. 5ATO USE CRUISE CONTROL J See Fig TO ADJUST MOWER CUTTING HEIGHT See FigTO ADJUST GAUGE WHEELS See Fig TO MOVE FORWARD AND BACKWARD See FigTO TRANSPORT See Figs. 3 and TO OPERATE MOWER See FigREVERSE OPERATION SYSTEM ROS See Fig TO OPERATE ON HILLSADD GASOLINE SERVICE REMINDER/HOUR METERBEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVELPURGE TRANSMISSION MOWING TIPSLUBRICATION CHART MAINTENANCEBLADE REMOVAL See Fig BATTERYTRACTOR BLADE CARETRANSAXLE PUMP FLUID ENGINEV-BELTS TRANSAXLE COOLINGAIR FILTER CLEANINGCLEAN AIR INTAKE/COOLING AREAS CLEAN AIR SCREENQ R AE SERVICE AND ADJUSTMENTSTO INSTALL MOWER See Figs TO REMOVE MOWER See FigE FJ H TO LEVEL MOWER TO REPLACE MOTION DRIVE BELT See Fig TO REPLACE MOWER BLADE DRIVE BELT See FigTO CHECK BRAKE TO REMOVE WHEEL FOR REPAIRS See Fig TO ADJUST STEERING WHEEL ALIGNMENTTO START ENGINE WITH A WEAK BATTERY See Fig FRONT WHEEL TOE-IN/CAMBERTO ADJUST CARBURETOR REPLACING BATTERY See FigTO REMOVE HOOD AND GRILL ASSEMBLY See Fig TO ADJUST THROTTLE CONTROL CABLEENGINE OIL STORAGEOTHER FUEL SYSTEMCORRECTION TROUBLESHOOTING POINTSPROBLEM CAUSEEngine dies when SCH10 SCHEMATICTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 IGNITION SWITCHT04S ELECTRICALWith Service Minder Option TRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45ELECTRICAL CHASSIS CHASSIS drive-texT2pedal10 DRIVEDRIVE engine-texKohl7 ENGINESPARK ARRESTER KIT ENGINE steering-texLEGND216 STEERING ASSEMBLYTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 wheelart1-tex DECALSWHEELS AND TIRES seat-tex6.5SL3 SEAT ASSEMBLY46texltpred3r6 MOWER DECKMOWER DECK lift-tex6 MOWER LIFTHUSQVARNA PRODUCT REGISTRATION INFORMATION & WARRANTY STATEMENT SECTION 4 EXCEPTIONS AND LIMITATIONS SECTION 2 HUSQVARNAS OBLIGATIONS UNDER THE WARRANTYSECTION 3 ITEMS NOT COVERED BY THIS WARRANTY SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATIONPrinted in the U.S.A 532 42 20-50R1 07.30.08 AP