Husqvarna 532 42 20-50_R1, 96045000408 Troubleshooting Points, Problem, Cause, Correction

Page 25
TROUBLESHOOTING POINTS

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

 

 

 

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

 

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

 

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

 

 

4.

Bad spark plug.

4.

Replace spark plug.

 

 

 

5.

Weak or dead battery.

5.

Recharge or replace battery.

 

 

 

6.

Dirty air filter.

6.

Clean/replace air filter.

 

 

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

 

 

8.

Water in fuel.

8.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

9.

Loose or damaged wiring.

9.

Check all wiring.

 

 

 

10.

Carburetor out of adjustment.

10.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

11.

Engine valves out of adjustment.

11.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

 

 

2.

Bad spark plug.

2.

Replace spark plug.

 

 

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

 

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

 

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

 

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Engine will not turn over

1.

Brake pedal not depressed.

1.

Depress brake pedal.

 

 

 

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

 

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

 

 

4.

Blown fuse.

4.

Replace fuse.

 

 

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

 

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

 

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

 

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

 

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Engine clicks but will not

1.

Weak or dead battery.

1.

Recharge or replace battery.

 

start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

 

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

 

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

 

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

 

 

3.

Build-up of grass, leaves and trash under mower.

3.

Clean underside of mower housing.

 

 

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

 

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

 

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

 

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

 

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

 

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

 

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

 

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

 

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

section.

 

 

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

Excessive vibration

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

 

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

 

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

Image 25
Contents Owners Manual / 96045000408 YTH20K46Safe Operation Practices for Ride-On Mowers SAFETY RULESI. GENERAL OPERATION II. SLOPE OPERATIONIII. CHILDREN V. SERVICEIV. TOWING PRODUCT SPECIFICATIONS TABLE OF CONTENTSCUSTOMER RESPONSIBILITIES TO CHECK BATTERY See Fig ASSEMBLYADJUST SEAT See Fig UNASSEMBLED PARTSCHECK DECK LEVELNESS CHECK TIRE PRESSURECHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEMOPERATION PH DG E KNOW YOUR TRACTORTO SET PARKING BRAKE See Fig HOW TO USE YOUR TRACTORSTOPPING See Fig. 5A TO USE THROTTLE CONTROL D See Fig. BTO ADJUST GAUGE WHEELS See Fig TO ADJUST MOWER CUTTING HEIGHT See FigTO MOVE FORWARD AND BACKWARD See Fig TO USE CRUISE CONTROL J See FigREVERSE OPERATION SYSTEM ROS See Fig TO OPERATE MOWER See FigTO OPERATE ON HILLS TO TRANSPORT See Figs. 3 andBEFORE STARTING THE ENGINE SERVICE REMINDER/HOUR METERCHECK ENGINE OIL LEVEL ADD GASOLINEPURGE TRANSMISSION MOWING TIPSLUBRICATION CHART MAINTENANCETRACTOR BATTERYBLADE CARE BLADE REMOVAL See FigV-BELTS ENGINETRANSAXLE COOLING TRANSAXLE PUMP FLUIDCLEAN AIR INTAKE/COOLING AREAS CLEANINGCLEAN AIR SCREEN AIR FILTERTO INSTALL MOWER See Figs SERVICE AND ADJUSTMENTSTO REMOVE MOWER See Fig Q R AEE FJ H TO LEVEL MOWER TO CHECK BRAKE TO REPLACE MOWER BLADE DRIVE BELT See FigTO REPLACE MOTION DRIVE BELT See Fig TO START ENGINE WITH A WEAK BATTERY See Fig TO ADJUST STEERING WHEEL ALIGNMENTFRONT WHEEL TOE-IN/CAMBER TO REMOVE WHEEL FOR REPAIRS See FigTO REMOVE HOOD AND GRILL ASSEMBLY See Fig REPLACING BATTERY See FigTO ADJUST THROTTLE CONTROL CABLE TO ADJUST CARBURETOROTHER STORAGEFUEL SYSTEM ENGINE OILPROBLEM TROUBLESHOOTING POINTSCAUSE CORRECTIONEngine dies when TRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 SCHEMATICIGNITION SWITCH SCH10With Service Minder Option ELECTRICALTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 T04SELECTRICAL CHASSIS CHASSIS drive-texT2pedal10 DRIVEDRIVE SPARK ARRESTER KIT ENGINEengine-texKohl7 ENGINE steering-texLEGND216 STEERING ASSEMBLYTRACTOR - - MODEL NUMBER YTH20K46 96045000408, PRODUCT NO. 960 45 WHEELS AND TIRES DECALSwheelart1-tex seat-tex6.5SL3 SEAT ASSEMBLY46texltpred3r6 MOWER DECKMOWER DECK lift-tex6 MOWER LIFTHUSQVARNA PRODUCT REGISTRATION INFORMATION & WARRANTY STATEMENT SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY SECTION 2 HUSQVARNAS OBLIGATIONS UNDER THE WARRANTYSECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION SECTION 4 EXCEPTIONS AND LIMITATIONSPrinted in the U.S.A 532 42 20-50R1 07.30.08 AP