Husqvarna 600CRT owner manual Unpacking Carton See Fig, Install Handle See Figs , 4

Page 6

ASSEMBLY

UNPACKING CARTON (See Fig. 2)

CAUTION: Be careful of exposed staples when handling or disposing of cartoning material.

IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES.

While holding handle assembly, cut cable ties securing handle assembly to top frame and depth stake. Let handle assembly rest on tiller.

Remove top frame of carton.

Slowly ease handle assembly up and place on top of carton.

Cut down right hand front and right hand rear corners of carton, lay side carton wall down.

Remove packing material from handle assembly.

HANDLE

ASSEMBLY

SHIFT ROD

FIG. 2

INSTALL HANDLE (See Figs. 3, 4, and 5)

Insert one handle lock (with teeth facing outward) in gearcase notch. (Apply grease on smooth side of handle lock to aid in keeping lock in place until handle assembly is lowered into position.)

VIEWED FROM R.H. SIDE OF TILLER

HANDLE ASSEMBLY

GEARCASE

NOTCH

HANDLE

LOCK

FIG. 3

Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position.

HANDLE ASSEMBLY "UP" POSITION

TIGHTEN HANDLE

LOCK LEVER TO

HOLD

LOOSEN HANDLE

LOCK LEVER TO

MOVE

FIG. 4

Rotate handle assembly down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loosely assemble locknut (See Fig. 5).

Insert pivot bolt in front part of plate and tighten.

Cut down remaining corners of carton and lay panels flat.

Lower the handle assembly. Tighten nut on carriage bolt so handle moves with some resistance. This will allow for easier adjustment.

Place flat washer on threaded end of handle lock lever.

Insert handle lock lever through handle base and gearcase. Screw in handle lock lever just enough to hold lever in place.

Insert second handle lock (with teeth inward) in the slot of the handle base (just inside of washer).

With handle assembly in lowest position, securely tighten handle lock lever by rotating clockwise. Leav- ing handle assembly in lowest position will make it easier to remove tiller from carton.

 

HANDLE

 

LOCK

GEARCASE

FLAT

 

WASHER

SLOT

HANDLE LOCK

 

 

LEVER

CARRIAGE

 

BOLT

 

 

PIVOT BOLT

HANDLE

LOCKNUT

BASE

 

FIG. 5

6

Image 6
Contents 600CRT Preparation Maintenance and StorageTraining OperationProduct Specifications Customer ResponsibilitiesTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller Forward Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Reverse Wheels ONLY/TINES StoppedTo Transport Before Starting EngineTurning ADD GasolineCultivating Tine Shear PinsTo Start Engine See Fig Tilling HintsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USEEngine AIR Filter See FigCooling System See Fig Service and Adjustments CleaningTiller Ground Drive Belt Adjustment See Fig To Remove Belt Guard See FigTo Replace Ground Drive Belt See Fig Tine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionRepair Parts Handle AssemblyMAINFRAME, Left Side KEY Part Description NO. noMAINFRAME, Right Side 532154354 Transmission Assembly Includes Key Nos Tine Shield Tine Assembly Tiller Model no CRT 954140070A DecalsWarranty Statement Husqvarna Forest & Garden CORev 9.28.98 TR