Husqvarna 965167936, 965168601, 965167501 manual Starting and Stopping, Starting and stopping

Page 21

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Starting

The chain brake must be engaged when the chain saw is started. Activate the brake by moving the front hand guard forwards.

Cold engine

Start position (1): Set the start/stop switch in the choke position by pulling the red control outward - upward (1).

Air purge (2): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled.

Warm engine

When the chain saw is heated restart the saw only by pulling the cord powerfully until the engine starts (5).

Never twist the starter cord around your hand.

There is a simplified start reminder with illustrations to describe each step on the rear edge of the saw (A).

As the chain brake is still engaged the speed of the engine must be set to idling as soon as possible, this is achieved by disengaging the throttle lock. Disengagement is done by gently touching on the throttle trigger. This prevents unnecessary wear to the clutch, clutch drum and brake band.

Then let the machine idle for a few seconds before you apply full throttle.

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

2

A

1

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires (3).

Push down the red choke control (4) as soon as the engine fires which can be heard through a "puff" sound. Keep on pulling the cord powerfully until the engine starts.

115 10 82-26 Rev.2 2008-06-03

Note! Reactivate the chain brake by pushing the front hand guard back towards the front handle. The chain

saw is now ready for use.

WARNING! Long term inhalation of the ! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a

health risk.

English 21

Image 21
Contents English 435 435e 440eKEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switchVibration damping system MufflerCutting equipment General rulesCutting equipment designed to reduce kickback General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Fitting the bar and chain Assembly435 435e, 440eFitting a spike bumper Fuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting and Stopping Starting and stoppingStarting Stopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueTree felling technique LimbingSafe distance Felling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral Immediately Checking the inertia brake releaseMuffler Starter Replacing the starter cordTensioning the recoil spring Air filter Replacing the return and drive springsFitting the starter Lubricating the bar tip sprocket Spark plugNeedle bearing lubrication Cooling systemAir Injection centrifugal cleaning Temperature -5C or colderWinter use Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122005, EN ISO ´z+S6¶68¨ Page 1151082-26