Husqvarna 965167501 Assembly, Fitting the bar and chain, 435e, 440e, Working with the chain

Page 17

ASSEMBLY

Fitting the bar and chain

 

!

 

WARNING! Always wear gloves, when

 

 

working with the chain.

 

 

 

 

435

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Unscrew the bar nut and remove the clutch cover (chain brake). Take off the transportation ring (A).

Fit the bar over the bar bolt. Place the bar in its rearmost position. Place the chain over the drive sprocket and in the groove on the bar. Begin on the top side of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

Mount the clutch cover and remember to fit the chain adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nut with your fingers.

Tension the chain by turning the chain tensioning screw clockwise using the combination spanner. The chain should be tensioned until it does not sag from the underside of the bar.

115 10 82-26 Rev.2 2008-06-03

The chain is correctly tensioned when there is no slack on the underside of the bar, and it can still be turned easily by hand.Tighten the bar nut with the combination spanner while holding up the tip of the bar.

When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life.

435e, 440e

Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.

Loosen the chain tensioner wheel and remove the clutch cover (chain brake). Remove the transport guard. (A)

Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing forward on the top edge of the bar.

English – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents English 435 435e 440eSymbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switchVibration damping system MufflerCutting equipment designed to reduce kickback Cutting equipmentGeneral rules General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain 435e, 440e 435Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain Assembly435 435e, 440eFitting a spike bumper Fuel Fuel HandlingFuelling Fuel safetyTransport and storage Long-term storageStarting Starting and StoppingStarting and stopping Stopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Directional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburettor adjustment Immediately Checking the inertia brake releaseMuffler Tensioning the recoil spring StarterReplacing the starter cord Fitting the starter Air filterReplacing the return and drive springs Lubricating the bar tip sprocket Spark plugNeedle bearing lubrication Cooling systemWinter use Air Injection centrifugal cleaningTemperature -5C or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsEN ISO 12100-22003, Cispr 122005, EN ISO EC-declaration of conformityApplies to Europe only ´z+S6¶68¨ Page 1151082-26
Top Page Image Contents