Fuelmixand chainoil
~WARNING! The chain saw is equipped with a
Fuel
|
|
|
|
|
|
| Always use a regular unleaded gasoline with minimum | |||||
|
|
|
|
|
|
| octane number of 90. |
|
|
| ||
|
|
|
|
|
|
| This engine is certified to operate on unleaded gasoline. | |||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| . For the best performance, use | |||||
|
|
|
|
|
|
|
| is especially developed for chain saws. |
| |||
J!Erp~In |
|
|
|
| ||||||||
|
|
|
| (. |
|
|
| Mixing ratio 1:50 (2 0/0), |
|
| ||
|
| ‘ | \, |
| . If | |||||||
M’‘ |
| ...> |
| “ h |
|
| another |
| ||||
|
|
|
|
| ||||||||
|
|
|
| ‘. |
|
| Mixing ratio 1:33 (3%). |
|
|
| ||
|
|
|
|
|
| countries where no | ||||||
|
| ~ | .\, . | |||||||||
|
|
| ‘G |
| 30 can be used. Mixing ratio 1:25 (4%). |
| ||||||
|
|
|
|
|
|
| . Never use | |||||
|
|
|
|
|
|
| . Always mix fuel and oil in a clean container. |
| ||||
|
|
|
|
|
|
| . Always start by filling half the amount of fuel, which is to be | |||||
|
|
|
|
|
|
|
| used, Then add the whole amount of oil. Mix (shake) the fuel | ||||
|
|
|
|
|
|
|
| mixture, Add the remaining amount of fuel, |
| |||
|
|
|
|
|
|
| . Mix (shake) the fuel mix thoroughly before filling the fuel tank | |||||
|
|
|
|
|
|
|
| on the saw. |
|
| f) |
|
|
|
|
|
|
|
|
| m |
|
|
| |
|
|
|
|
|
|
|
|
|
| b |
| |
|
|
|
|
|
|
|
| Gasolin |
| Oil .01. | Huile . Aceite |
|
|
|
|
|
|
|
|
| fci |
| |||
|
|
|
|
|
|
|
| Benzin |
|
| Lit. |
|
|
|
| l\ |
|
|
|
| Essence |
|
|
| |
|
|
|
|
|
|
| Gasolina | 2%(1 :50) | 3“/0(1:33) 4%(1 :25) | 5%(1:20) | ||
|
|
|
|
|
|
| Lit | |||||
|
|
|
|
|
|
|
| 5 | 0,10 | 0,15 | 0,20 | 0,25 |
|
|
|
|
|
|
|
| 10 | 0,20” | 0,30 | 0,40 | 0,50 |
|
|
|
|
|
|
|
| 15 | 0,30 | 0,45 | 0,60 | 0,75 |
|
|
|
|
|
|
|
| 20- | 0,40 | 0,60 | 0,80 | 1,00 |
D& Chain oil
9
9
:
Min 3 m m
(lo ft)
m
m
*
Chain oil
●The chain lubrication svstem is automatic, Alwavs use s~ecial
chain oil with oood adhesive characteristics. ‘
. In countries w;ere no special chain oil is available, gear box oil EP 90 can be used,
. Never use waste oil. This results in damage to the oil pump, the bar and the chain.
. It is important to use oil of the right viscosity according to the a temperature.
●In temperatures below OOC(320F)some oils become less viscous. This can overload the oil pump and result in damage to the oil pump components.
✎Contact your servicing dealer when choosing chain oil.
Fueling
I | i |
~WARNING!
●Always shut off the engine before refueling.
●Slowly open the fuel tank, when filling up with fuel, so that possible over- pressure disappears.
●Tighten the fuel cap carefully, after fueling.
●Always move the saw away from the fueling area before starting.
Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank and causes malfunction. Make sure that the fuel is well mixed by shaking the container, before fueling. The volume of the chain oil tank and the fuel tank are adjusted to each other. Therefore, always fill up with chain oil and fuel at the same time.