Husqvarna 362XP manual Muffler, Starter, Changing a broken or worn starter cord

Page 32

MAINTENANCE

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush. A blocked mesh will cause the engine to overheat and may lead to serious damage.

Note! The mesh must be replaced if it is damaged. If the mesh is blocked the machine will overheat and this will cause damage to the cylinder and piston. Never use a machine with a muffler that is in poor condition.

Never use a muffler if the spark arrestor mesh is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator.The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odorless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley.

Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 362XP Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lock Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Tensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting Lubricating cutting equipment Checking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock Changing a broken or worn starter cord MufflerStarter Air filter Spark plugTensioning the recoil spring Changing a broken recoil springAdjustment of the oil pump Air Injection centrifugal cleaningLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C 23F or colder Heated handlesElectrical carburetor heating CanadaMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage 1150061-95 ´z+R&3¶5w¨ ´z+R&3¶5w¨

362XP specifications

The Husqvarna 362XP is a professional-grade chainsaw designed to meet the demanding needs of forestry workers, landscapers, and tree care professionals. Known for its robust performance and reliability, the 362XP is a powerful tool that balances performance with user comfort.

One of the standout features of the Husqvarna 362XP is its engine. It is equipped with a potent 60.3 cc, 2-stroke engine that provides high power output while remaining lightweight, making it ideal for extended use in the field. This chainsaw is designed with an X-Torq engine technology, which not only delivers reduced fuel consumption but also minimizes emissions, making it more environmentally friendly. The engine's design contributes to its excellent torque over a wide rpm range, allowing for efficient cutting in various materials.

The Husqvarna 362XP boasts an easy-start system, which is particularly beneficial in cold conditions. The Smart Start technology ensures that the saw starts with minimal effort, allowing users to get to work quickly. Coupled with a powerful ignition system, the chainsaw provides reliable performance that is consistent and dependable.

Another significant feature of the 362XP is its ergonomic design. The handle is designed for optimal grip and comfort, reducing user fatigue during long working hours. The anti-vibration technology integrated into the chainsaw minimizes vibrations transferred to the user's hands, further enhancing comfort and control while operating the machine.

The chainsaw is equipped with a lightweight, durable guide bar and a high-quality chain, designed to set the standard for cutting capabilities. The chain tensioning system is easy to use and allows for quick adjustments without the need for additional tools. This feature is essential for professionals who need to stay efficient while working on the job.

Safety is a priority with the Husqvarna 362XP, which includes features like a chain brake that activates in case of kickback and reinforced protective features to minimize the risk of injury. Additionally, the air filter system offers excellent filtration to ensure the engine runs smoothly in a variety of conditions.

In summary, the Husqvarna 362XP is a cutting-edge chainsaw engineered for performance, comfort, and safety. Its combination of advanced technology, powerful engine, ergonomic design, and superior safety features make it a top choice for professionals in need of a reliable and efficient cutting tool. Whether dealing with heavy-duty tasks or delicate trimming, the 362XP proves to be a formidable companion in any arborist's toolkit.
Top Page Image Contents