Husqvarna 968999218, 968999214, 968999216, BZ7234D, BZ6127D, BZ6134D manual Checking the Parking Brake

Page 36

MAINTENANCE

system, it is necessary to open both these valves to drain the radiator completely.

When refilling the system, it is important that all trapped air be purged. The following procedure will help to insure this:

1.Make sure the engine is level. Fill the overflow reservoir up to the MAX mark with coolant mixture.

2.Slowly fill the radiator to the bottom of the filler neck with coolant mixture.

3.With radiator cap off, start the engine and let it warm up (no-load). Then, if necessary, add more coolant mixture to bring the level back up to the bottom of the filler neck.

4.Reinstall the radiator cap and run the engine a short time with the system sealed while watching the temperature gauge. If the temperature gauge goes past 230 degrees and does not drop back to approximately 190 degrees, indicating the thermostat has opened, allow the engine to cool down, check for leaks and repeat the procedure.

This is a sealed system. If it becomes necessary to add coolant mixture at a later date, check for leaks and if the overflow reservoir has not been drained completely, add coolant mixture to the reservoir only. This will help prevent air pockets in the radiator top tank and lessen the chance of introducing contaminates to the system.

Checking the Parking Brake

Visually check that no damage is found on the lever, links, or switch belonging to the parking brake. Perform a test drive and check that there is a braking effect.

To adjust the parking brake:

1.Set brake lever (D) fully forward against stop.

NOTE: Brake cross shaft MUST be properly lubricated and both cross shaft and over- center assemblies (F) MUST rotate freely.

2.Loosen jam nut (A) at rear of clevis (B) and remove clevis pin (C) both sides of mower.

3.Rotate over-center assembly (F) in correct direction (clockwise on left

Overflow bottle

BAM-20

 

 

 

 

 

Parking brake in the disengaged position

BAM-4

 

 

 

 

 

Parking brake linkage.

34

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Operators Manual Models Page Contents OPERATOR’S ManualPage Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxx xxxxxx Safety Instructions Safety InstructionsGeneral Use Keep children away from the work area Driving on Slopes Do as followsMaintenance Children8011-563 Transport Important InformationControls PresentationComponent Locations Gauges Throttle ControlIgnition Hour MeterSeat Adjustment Engaging the Mower DeckParking Brake Motion Control Levers Motion Control LeversHydraulic Lift Switch Refueling Fuel Shut-OffFuses Manual Lifting Lever with Foot Assist for the Mower Deck Hydraulic Lift for the Mower DeckPin must be locked into a hole for transport or mowing Accessories RelaysOperation RunningBefore Starting Starting the EngineSet the throttle Open the fuel switch for the selected fuel tank Running Released parking brakeEngaging the mower deck Mowing Tips Operation Stopping the Engine Moving by HandMaintenance MaintenanceMaintenance Schedule 150 Checking the Safety System Mower Deck LevelingChecking and Adjusting the Throttle Cable Clutch Service and MaintenanceChecking the Engines Cooling Air Intake Replacing the Air Filter Paper filterReplacing the Fuel Filter Checking Tire PressuresCheck and Filling Coolant System Checking the Parking Brake Cleaning and Washing Checking the BladesChecking Battery Checking the Hydraulic System125 gal Reverse Detent Adjustment Motion Control Linkage AdjustmentDampener Mounting Keep hands, feet and clothing away from rotating tiresMaintenance Lubrication LubricationLubrication Schedule 150h Lubricating the Cables Lubricating in Accordance with the Lubrication ScheduleHydraulic System, Oil Level Changing Oil and FiltersEngine Oil Changing the Engine Oil Checking the Oil LevelThrottle Cable, Lever Bearings Belt Adjuster, Mower Deck Front Wheel MountFront Wheel Bearings Belt Adjuster Mule Drive Idler Arm Steering Control Shafts Tip the driver’s seatMower Deck Struts Belt Adjuster, Hydraulic Pumps Changing the Oil FilterTrouble Shooting Guide Trouble Shooting GuideProblem Cause Trouble Shooting Guide Trouble Shooting Guide Service StorageStorage Winter StorageTechnical Data Technical DataMeasurements, Weights, Etc EngineNoise Emissions and Cutting Width Electrical SystemTransmission Mower DeckService Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 50 Hours DailyHour Service Service Journal Service Journal Service Journal At Least Once Each Year Service Journal Wiring Schematic Wiring Schematic

BZ6134D, BZ6127D, BZ7234D, 968999216, 968999214 specifications

Husqvarna, a renowned name in the outdoor power equipment industry, offers a diverse range of lawn mowers and robotic solutions designed to meet various mowing needs. Among their impressive lineup are the models Husqvarna 968999218, 968999216, BZ6134D, BZ7234D, and BZ6127D. Each model showcases advanced features and technologies that enhance performance, efficiency, and user experience.

The Husqvarna 968999218 and 968999216 are part of Husqvarna's innovative robotic mower series. These mowers leverage the latest GPS-assisted navigation technology, allowing for precise mapping and efficient mowing patterns. The cutting-edge robotic mowers are equipped with smart technology that enables them to detect various terrains and adapt their cutting strategy accordingly. Both models can operate on slopes up to 24 degrees, thanks to their powerful traction system, ensuring a thorough and even cut regardless of the landscape.

In terms of connectivity, these robotic models feature integration with smartphone apps, enabling users to monitor and control mowing schedules remotely. This convenience makes managing lawn care effortless. Furthermore, they are designed with a weatherproof construction, allowing for operation across varying weather conditions, ensuring reliable performance year-round.

The BZ6134D, BZ7234D, and BZ6127D models represent Husqvarna's commitment to traditional lawn mowing, featuring robust design and advanced engineering. These walk-behind mowers are powered by reliable engines that deliver exceptional cutting performance. The cutting decks are constructed from durable materials, providing longevity and resistance to wear and tear.

The BZ7234D stands out with its larger cutting deck and enhanced maneuverability, ideal for larger lawns and more complex landscapes. It also boasts an adjustable cutting height, allowing users to customize the mowing height according to their lawn's needs.

All models are designed with user comfort in mind, featuring ergonomic handles and lightweight designs that make them easy to maneuver. With a focus on efficiency, these mowers utilize advanced blade technology to produce clean cuts while minimizing fuel consumption. Additionally, the incorporation of easy-start mechanisms ensures that the mowers are user-friendly and ready for operation with minimal effort.

In summary, the Husqvarna 968999218, 968999216, BZ6134D, BZ7234D, and BZ6127D exemplify quality and innovation in lawn care. With advanced features, robust construction, and a user-centric design, these models are tailored to meet the diverse needs of homeowners and professionals alike, making lawn maintenance an effortless task.
Top Page Image Contents