Husqvarna PR 17 AWD, PF 21 AWD manual Driving, Cutting tips, Before starting, Start the engine

Page 17

Driving

Cutting tips

WARNING! Clear the lawn from stones and

!other objects which can be thrown out by the blades.

•Localise and mark stones and other fixed objects to avoid collision.

•Start with a high cutting height and reduce down until the required mowing results are obtained.

•The mowing results are best with a high engine speed (fast rotating blades) and low driving speed (slow moving machine). If the grass is not too high and thick, the driving speed can be increased without noticeably depreciating the mowing result.

•The best lawns are achieved if the grass is cut often. Mowing becomes more uniform and the grass cuttings become more evenly distributed over the surface. The total time consumption is not greater since it is possible to select a higher driving speed without inferior mowing results.

•Avoid mowing a wet lawn. The mowing results are inferior since the wheels sink down into the soft lawn.

•Hose down the cutting unit with water underneath each time it is used. The cutting unit should then be put in the service position.

•When the BioClip function is used, it is very important that the mowing interval is not too long.

WARNING! Do not use the machine on

!ground that slopes more than 10°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction.

Before starting

•Read the safety instructions and information concerning the placement of controls and functions before starting.

•Perform daily maintenance before starting as set out in the Maintenance schedule.

IMPORTANT INFORMATION

The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage.

Start the engine

1Make sure that the clutch control is depressed. PR 17 AWD and PF 21 AWD have one control for the front axle and one control for the rear axle.

2Lift up the cutting unit by pulling the lever backwards to locked position (transport position) and apply the parking brake.

2

1

The engine can not be started if the parking brake is not pressed down.

3 Move the throttle control to the middle position.

English – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PR 17 PR 17 AWD PF 21 PF 21 AWD Contents After the first 8 hours Service journalPre-delivery service Dear Customer IntroductionDriving and transport on public roads TowingSerial Number Good serviceSymbols KEY to SymbolsBrake Starting instructions Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Location of the controls What is WHAT?Presentation Mechanical Lifting Lever for Cutting Unit Cutting unitLever for hydraulic lift of attachments Exercise care and refuel outdoors see safety instructions Cutting height adjustment leverSeat FuellingRelease lever Lights and power outletClutch control PR 17 AWD and PF 21 AWD Clutch control PR 17 and PFCutting tips DrivingBefore starting Start the engineRemove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Braking Driving the RiderStop the engine Page Maintenance schedule MaintenanceOnce a Before starting MaintenanceRemoving of the machine hoods CleaningAdjusting the parking brake PR 17, PF Checking and adjusting the steering wiresAdjusting the parking brake PR 17 AWD, PF 21 AWD Can result in reduced braking abilityReplacement of fuel filter Checking and adjusting of throttle wireChecking and adjusting the choke wire Checking the transmission’s air intake Checking the fuel pump’s air filterReplacing the air filter Cool before starting to replace the air filterCleaning the engine and muffler Check the level of the battery acidIgnition system Replacing the spark plugCheck the safety system Checking the tyre pressure Replacing the light bulbsMain fuse Checking the engine’s cooling air intake When the engine is running. Mind your fingersReplacing the rear drive belt PR 17 and PF RemovalAssembly Replacing the centre belt Trapping your hand Replacing the front beltFitting the cutting head Removing the cutting unit Replacing the cutting unit belts Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Placing in the service position Service position for the cutting unitRemoving the BioClip plug Restoring from service positionChecking the blades Lubrication Driver seat Lubricating the belt adjusterThrottle and choke cables, lever bearings Checking the engine’s oil levelReplacing the engine oil Lubricate the hydrostatic cable with linksChanging the oil filter Parking brake cable PR 17 and PF Hydraulic oil filter changeParking brake cable PR 17 AWD and PF 21 AWD Checking the transmission oil levelProblem Procedure Troubleshooting schedulePR 17 and PR 17 AWD Electrical and Hydraulic SystemsPF 21 and PF 21 AWD Wiring diagram PR 17, PR 17 AWD, PF Hydraulic SystemStorage ServiceWinter storage GuardTechnical data ´z+S¶6@¨ 50 English´z+S¶6@¨ Cutting unit CombiTurf EC-declaration of conformity Applies to Europe only1151089-26 ´z+S¶6@¨ ´z+S¶6@¨

PR 17, PF 21, PR 17 AWD, PF 21 AWD specifications

The Husqvarna PR 17, PR 17 AWD, PF 21, and PF 21 AWD are advanced pressure washers designed to deliver optimal performance, versatility, and convenience for various cleaning tasks. These models are engineered to cater to both residential and professional users, ensuring that maintaining cleanliness becomes an effortless task.

The Husqvarna PR 17 is a powerful pressure washer that sports a robust design, making it ideal for tackling medium to heavy-duty cleaning jobs. With a maximum pressure output of 1700 PSI and a flow rate of 1.2 GPM, it can efficiently clean driveways, patios, and vehicles. The PR 17 is equipped with an adjustable spray nozzle, providing users with the option to switch between different spray patterns, enhancing its versatility for different surfaces.

For those looking for added traction and stability, the PR 17 AWD (All-Wheel Drive) variant features a sophisticated four-wheel drive system. This technology ensures enhanced maneuverability over uneven terrains and difficult surfaces. The AWD feature is particularly beneficial for users who require improved mobility, whether it's on inclines or rough outdoor environments.

Moving to the PF 21 series, the Husqvarna PF 21 and PF 21 AWD both offer exceptional cleaning performance with their impressive specifications. The PF 21 boasts a powerful motor capable of delivering up to 2100 PSI, making it suitable for more demanding tasks. With a generous flow rate of 1.4 GPM, it can easily remove dirt and grime from larger areas efficiently. The PF 21 comes equipped with a set of interchangeable nozzles, allowing users to adjust the pressure according to their specific cleaning needs.

The PF 21 AWD model adds the all-wheel drive feature, enhancing the user experience by making it easier to navigate while cleaning larger spaces. This model is perfect for professionals and homeowners who require a reliable machine for frequent use. The ergonomic design of both PF 21 models ensures ease of handling and minimizes user fatigue, even during extended cleaning sessions.

These Husqvarna pressure washers also prioritize durability and maintenance ease. With features such as durable steel frames and easily accessible components, users can expect a long lifespan and hassle-free upkeep.

In summary, whether you choose the PR 17, PR 17 AWD, PF 21, or PF 21 AWD, each model offers unique features tailored to a range of cleaning tasks. Their combination of power, technology, and user-friendly designs make them an excellent choice for anyone looking to achieve spotless results.
Top Page Image Contents