Husqvarna iZ4217TSKAA, iZ4817TSKAA, iZ4821TSKAA, iZ5223TKOA, iZ5225TXPKOA, iZ6125TKOA, iZ5223TVAN

Page 56

LUBRICATION

3.Engine Oil Kohler Engine Changing the Engine Oil

Change oil after every 100 hours of operation (more frequently under severe conditions). Refill with service class SG, SH, SJ or higher oil as specified in the Viscosity Grades table on page 56.

Change the oil while the engine is still warm. The oil will flow more freely and carry away more impurities. Make sure the engine is level when filling, checking or changing the oil.

WARNING!

The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust sytem to cool at least two (2) minutes.

Change the oil as follows:

1.To keep dirt, debris, etc., out of the engine, clean the area around the oil fill cap/dipstick before removing it.

2.Remove the oil drain plug and the oil fill cap/dipstick. Be sure to allow ample time for complete drainage.

3.Reinstall the drain plug. Make sure it is tightened to 10 ft.lb. (13.6 Nm) torque.

4.Fill the crankcase, with new oil of the proper type, to the “FULL” mark on the dipstick. Refer to Oil Type, page 56. Always check the level with the dipstick before adding more oil.

5.Reinstall the oil fill cap/dipstick and tighten securely.

IMPORTANT INFORMATION

To prevent extensive engine wear or damage, always maintain the proper oil level in the crankcase. Never operate the engine with the oil level below the “ADD” mark or over the “FULL” mark on the dipstick.

6.Start the engine. Run it for a few seconds and recheck the oil level.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

English-54

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Operators manual Page Contents OPERATOR’S Manual RiderEnglish-2 Introduction IntroductionGood Service Manufacturing NumberXxxx xxxxxx Symbols and DecalsSymbols and Decals Repair work General Operation Safety InstructionsSafety Instructions English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Risk of sparking Transport Important InformationRoll over Protecion system Rops Customer responsibilitiesControl Locations ControlsControls Motion Control Levers Parking Brake Hour MeterTracking Knob Fuses Blade switchIgnition Switch Seat Locking Device RefuelingChoke Control Seat Adjustment LeverFuel Shut Off Valve Throttle Control Lifting Lever for the Mower DeckCutting height pedal AccessoriesPump release valves Training OperationOperation Starting the Engine Roll bar and safety beltBefore Starting Disengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position USE Full Throttle When Mowing To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule Maintenance= Described in this manual  = Not described in this manual Battery To clean battery and terminalsReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Safety system Checking the Engines Cooling Air Intake Checking and Adjusting Throttle CableChecking and Adjusting the Choke Cable Replacing the Air Filter Standard air filterCyclon air filter maintenance Filter replacement Air filter indicator optionalReplacing the Fuel Filter Checking the Fuel Pump’s Air FilterFaulty adjustment can cause an accident Checking Tire PressuresChecking the Parking Brake Checking the V-beltsChecking the Blades Pump beltRemove blade bolt by turning counterclockwise Adjusting the Mower Deck Adjusting Cutting HeightTo adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingRemoval and installation of caster wheel Caster WheelsLubrication Schedule LubricationLubrication Lubricating in Accordance with the Lubrication Schedule Lubricating the CablesShaft Bushings and Linkage Engine Oil Kohler Engine Changing the Engine Oil Checking the Oil Level Oil Recommendations Oil TypeEngine Oil Kawasaki Engine Changing the Engine Oil Throttle and Choke Cables, Lever Bearings Front Wheel MountDeck belt pulleys Mower Deck Height AdjusterFront Wheel Bearings Belt Adjuster, Mower Deck Mower Deck StrutsBrake Arms Changing the Oil Filter Problem Cause Trouble Shooting GuideTrouble Shooting Guide English-64 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramsTechnical Data IZ5225TXPKOA IZ5223TVAN IZ6125TKOAEquipment IZ4217TSKAA IZ4817TSKAA IZ4821TKAA Overall dimensions IZ5223TKOA CV23SEnglish-72 Torque Specifications USA requirements Conformity CertificatesConformity Certificates Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 8 Hours Hour Service English-78 English-79 English-80 At Least Once Each Year English-82 English-83 English-84 Page 114090Rir08/21/06

iZ4217TSKAA, iZ4817TSKAA, iZ4821TSKAA, iZ5223TKOA, iZ5225TXPKOA, iZ6125TKOA, iZ5223TVAN specifications

Husqvarna, a renowned name in outdoor power equipment, has a stellar lineup of zero-turn mowers that cater to both residential and commercial users. Their models, including the iZ4217TSKAA, iZ4817TSKAA, iZ4821TSKAA, iZ5223TKOA, iZ5225TXPKOA, iZ6125TKOA, and iZ5223TVAN, are designed with advanced technologies to enhance performance and user experience.

The iZ4217TSKAA is powered by a robust engine that delivers reliable performance for small to medium-sized lawns. It features a 21-inch cutting deck, making it ideal for maneuvering in tight spaces. The unit's intuitive controls ensure ease of operation while providing a smooth mowing experience.

Moving up the line, the iZ4817TSKAA offers increased power with a larger engine and a wider cutting deck. Its superior cutting technology provides a clean cut, while adjustable cutting heights allow users to customize their mowing experience. The model is engineered for durability, ensuring it withstands rigorous use over varying terrains.

The iZ4821TSKAA takes performance a step further with enhanced stability and traction. It includes all the features of its predecessor, coupled with a bigger deck, which significantly reduces mowing time. Its heavy-duty frame and rubberized tires improve grip on slopes, making it perfect for diverse landscapes.

For those looking for commercial-grade performance, the iZ5223TKOA is an excellent choice. With an impressive 23 horsepower engine, it delivers unmatched power and efficiency. Its cutting-edge air filtration system prolongs engine life, making it ideal for frequent use.

The iZ5225TXPKOA is designed for ultimate comfort, incorporating an ergonomic seating system that reduces operator fatigue during long mowing sessions. This model also features additional storage compartments, making it convenient for transporting tools and personal items.

Another heavy-duty option is the iZ6125TKOA, designed for professional landscapers. It boasts a 25 HP engine and a large cutting deck for maximum productivity. Its advanced suspension system offers superior ride quality even on bumpy terrains, while integrated safety features ensure a secure mowing experience.

Finally, the iZ5223TVAN combines versatility and power. Its innovative design allows for easy attachment of various accessories, making it a multifunctional tool in any landscaping arsenal. With a focus on user-friendly controls, this mower delivers a compelling performance for both novice and seasoned users.

Each of these Husqvarna models exemplifies the brand's commitment to quality and innovation, ensuring that whether for personal or professional use, users can achieve unparalleled results while enjoying the efficiency and reliability that Husqvarna mowers offer.
Top Page Image Contents