Husqvarna IZ 21 manual Blade switch, Ignition Switch, Fuses

Page 21

CONTROLS

5. Blade switch

In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed.

6. Ignition Switch

The ignition key is placed in the ignition switch on the driver s panel and is used to start and stop the engine.

IMPORTANT INFORMATION

Do not run the starter for more than five seconds each time. If the engine does not start, wait about 10 seconds before re- trying.

7. Fuses

The fuses are located in a holder to the left of the hydraulic tank. They are flat pin fuses of the same type used in automobiles.

There are three fuses, as well as socket for one spare fuse.

Fuse ratings and functions:

¥20 A, Primary fuse.

¥7.5 A, Mower deck coupling.

¥7.5.A, Accessory outlet.

¥Socket for spare fuse.

8011-510

Blade Switch

8011-521

Ignition key and hour meter

8011-443

Fuses

English-19

Image 21

Contents English Operator´s manualPage Operator S Manual Rider ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Passengers Safety Instructions Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Risk of sparking Transport Customer responsibilities Controls ControlsControl Locations Motion Control Levers Hour Meter Tracking KnobParking Brake Blade switch Ignition SwitchFuses Refueling Seat Locking DeviceSeat Adjustment Lever Fuel Shut Off ValveChoke Control Lifting Lever for the Mower Deck Throttle ControlPump release valves AccessoriesCutting height pedal Tunnel Deck OnlyOperation OperationTraining Starting the Engine Before StartingDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position USE Full Throttle When Mowing To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule MaintenanceBefore After To clean battery and terminals BatteryReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Safety system Checking and Adjusting Throttle Cable Checking and Adjusting the Choke CableChecking the Engine’s Cooling Air Intake Standard air filter Replacing the Air FilterCyclon air filter maintenance Air filter indicator optional Filter replacementChecking the Fuel Pump s Air Filter Replacing the Fuel FilterChecking Tire Pressures Faulty adjustment can cause an accidentChecking the Parking Brake Checking the V-beltsPump belt Checking the BladesBlade attachment Adjusting Cutting Height Adjusting the Mower DeckTo adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsLubrication LubricationLubrication Schedule Lubricating the Cables Shaft Bushings and LinkageLubricating in Accordance with the Lubrication Schedule Checking the Oil Level Engine Oil Changing the Engine OilFront Wheel Mount Throttle and Choke Cables, Lever BearingsMower Deck Height Adjuster Front Wheel BearingsDeck belt pulleys Tunnel Deck Only Mower Deck Struts Belt Adjuster, Mower DeckBrake Arms Changing the Oil Filter Trouble Shooting Guide Trouble Shooting GuideProblem Cause English-61 Storage ServiceStorage Winter StorageWiring diagram Wiring DiagramsEngine IZ21C Technical DataManufacturer TransmissionIZ21C Tunnel Deck Combi Deck Accessories Standard HardwareMetric Standard Hardware Conformity Certiﬁcates For Model Listed Below Conformity CertificatesBusiness Name & Address Notiﬁed BodyService Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signEnglish-69 Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 English-76 Page 2010W19 Original instructions 115 36