Husqvarna EZ4621, EZ6124, EZ5226, EZ4822 Battery, To clean battery and terminals, Replacing battery

Page 38

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean. Keep battery bolts tight.

Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Open the terminal access doors.

2.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until shiny.

5.Coat terminals with grease or petroleum jelly

6.Reinstall battery.

Replacing battery

1.Lift Seat and rotate forward.

2.Open terminal access doors.

3.Using two 1/2" wrenches disconnect BLACK battery cable then RED battery cable.

4.Using 7/16" wrench, remove terminal guard.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall terminal guard.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

10.Tighten securely.

11.Close terminal access doors.

12.Lower seat.

Always use protective glasses when handling the battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

CZ-22

1.Terminal guard

2.Terminal access doors Battery installation

English-39

Image 38
Contents Operator’s Manual EnglishContents OPERATOR’S ManualPage Introduction Good Service Manufacturing NumberSymbols and Decals Xxxx xxxxxx xxxxx Xxxxxxxxx xxxxxx Xx xxxxxxxx xxxxRead General Operation SafetySafety Instructions Never take passengers Personal Safety Equipment Slope OperationChildren Safe Handling of Gasoline MaintenanceGeneral Maintenance Never drive the machine in an enclosed space Risk of sparking Transport Customer responsibilities Controls ControlsParking Brake Steering Control LeversTracking Seat adjustment boltsFuel Shut Off Valve Refueling By pass linkage FusesChoke Control Ignition SwitchHour Meter Blade switch Throttle ControlAccessories Cutting height pedalTraining OperationOperation To move forward and backwardBefore Starting Starting the EngineMove the throttle to the middle position Open the fuel shut off valve Gradually press in the choke control To remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Running Operating on hills Mowing Tips Stopping the EngineLeaving the ignition switch in any other Moving by Hand Maintenance Schedule MaintenanceMaintenance English-38 Replacing battery BatteryTo clean battery and terminals Checking the Safety System Ignition SystemChecking the Engine’s Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Replacing the Air Filter Briggs & Stratton Engine Standard air filterReplacing the Air Filter Kohler Engine Servicing PrecleanerService Paper Element Replacing Heavy Duty Air Filter Checking Tire Pressures Replacing the Fuel FilterChecking the Fuel Pump’s Air Filter Deck belt Checking the Parking BrakeChecking the V-belts To replace deck beltDeck belt installation To replace IZT Integraded Zeroturn Transaxle belt Belt installationIZT belt IZT belt removalChecking the Blades Blade replacement Leveling Adjusting the Mower DeckAdjusting Cutting Height To adjust anti-scalp rollers Caster Wheels Cleaning and WashingRemoval and installation of caster wheel HardwareMower is tracking to the right Tracking adjustmentTo adjust parking brake Mower is tracking to the leftGeneral LubricationLubrication Lubrication ScheduleFront Wheel Mount Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Front Wheel BearingsDeck outer spindle Engine Oil Changing the Engine OilChecking the Oil Level Changing the Engine Oil Filter Transaxle Transmission Fluid ChangeDrain old oil filters of all free flowing oil prior to Purging Procedures Problem Cause Trouble Shooting GuideTrouble Shooting Guide English-63 English-64 Storage ServiceStorage Winter StorageWiring Diagram EZ4624 EZ5226 Engine Technical DataTechnical Data TransmissionTechnical Data EZ4624 EZ5226 Equipment EZ4220 EZ4822 Engine EZ 4220 EZ4822 Equipment Technical Data Productivity USA requirements Conformity CertificatesConformity Certificates CE requirementsDelivery Service Service JournalService Journal Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-78 English-79 Service Journal At Least Once Each Year Service Journal Page Page Part No 131329Rir 07/02/07