Husqvarna EZ4822, EZ6124 To replace IZT Integraded Zeroturn Transaxle belt, IZT belt removal

Page 47

MAINTENANCE

IZT belt

To replace IZT (Integraded Zeroturn Transaxle) belt

Park the mower on a level surface. Engage the park brake.

IZT belt removal

NOTE: Be careful not to damage the fan blades on the IZT as this can affect cooling or damage the IZT

Remove the deck belt (see to replace deck belt in this section of the manual).

Create slack in the belt by either removing the spring on the pump idler arm or inserting 1/2" breaker bar into the square hole on the spring loaded idler. Rotate arm to release belt tension.

The belt should now be able to be removed from the engine pulley and IZT pulleys.

Belt installation

Wrap the IZT belt around the IZT pulleys.

Route the belt around the inside of the idler pulley.

Now you can wrap the belt around the engine pulley.

Reattach the spring on the pump idler arm if previously disconnected.

Reinstall the deck belt onto the electric clutch pulley (see to replace deck belt in this section of the manual).

4

3

 

1

2

5

 

 

8058-008

1.Spring loaded idler pulley

2.Fixed idler pulley

3.Electric clutch

4.IZT belt

5.Deck belt

IZT belt

 

 

3

 

 

 

4

 

5

1

2

6

7

8058-009

1.Spring loaded idler pulley

2.Fixed idler pulley

3.Engine

4.IZT belt

5.Left drive pulley

6.Right drive pulley

7.Square hole

IZT belt routing

English-48

Image 47
Contents English Operator’s ManualOPERATOR’S Manual ContentsPage Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx Xxxxxxxxx xxxxxx Xx xxxxxxxx xxxx Symbols and DecalsRead General Operation SafetySafety Instructions Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline MaintenanceGeneral Maintenance Never drive the machine in an enclosed space Risk of sparking Transport Customer responsibilities Controls ControlsSteering Control Levers Parking BrakeTracking Seat adjustment boltsFuel Shut Off Valve Refueling Fuses By pass linkageChoke Control Ignition SwitchHour Meter Throttle Control Blade switchCutting height pedal AccessoriesTo move forward and backward OperationOperation TrainingStarting the Engine Before StartingMove the throttle to the middle position Open the fuel shut off valve Gradually press in the choke control To remove cables, reverse order To start an engine with a weak batteryTo attach jumper cables Running Operating on hills Stopping the Engine Mowing TipsLeaving the ignition switch in any other Moving by Hand Maintenance Schedule MaintenanceMaintenance English-38 Replacing battery BatteryTo clean battery and terminals Ignition System Checking the Safety SystemChecking the Engine’s Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Standard air filter Replacing the Air Filter Briggs & Stratton EngineReplacing the Air Filter Kohler Engine Servicing PrecleanerService Paper Element Replacing Heavy Duty Air Filter Checking Tire Pressures Replacing the Fuel FilterChecking the Fuel Pump’s Air Filter To replace deck belt Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation IZT belt removal Belt installationIZT belt To replace IZT Integraded Zeroturn Transaxle beltChecking the Blades Blade replacement Leveling Adjusting the Mower DeckAdjusting Cutting Height To adjust anti-scalp rollers Hardware Cleaning and WashingRemoval and installation of caster wheel Caster WheelsMower is tracking to the left Tracking adjustmentTo adjust parking brake Mower is tracking to the rightLubrication Schedule LubricationLubrication GeneralFront Wheel Bearings Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Front Wheel MountEngine Oil Changing the Engine Oil Deck outer spindleChecking the Oil Level Transaxle Transmission Fluid Change Changing the Engine Oil FilterDrain old oil filters of all free flowing oil prior to Purging Procedures Problem Cause Trouble Shooting GuideTrouble Shooting Guide English-63 English-64 Winter Storage ServiceStorage StorageWiring Diagram Transmission Technical DataTechnical Data EZ4624 EZ5226 EngineTechnical Data EZ4624 EZ5226 Equipment EZ4220 EZ4822 Engine EZ 4220 EZ4822 Equipment Technical Data Productivity CE requirements Conformity CertificatesConformity Certificates USA requirementsAction Date, mtr reading, stamp, sign Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-78 English-79 Service Journal At Least Once Each Year Service Journal Page Page Part No 131329Rir 07/02/07