Husqvarna Z18 manual Adjusting the Mower Deck

Page 48

MAINTENANCE

Install new or re-sharpened blade with stamped "GRASS SIDE" facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing.

Install and tighten blade bolt securely.

Torque blade bolt to 27-35 ft/lb (35-45 Nm).

IMPORTANT INFORMATION

Special blade bolt is heat treated.

Replace with a Husqvarna bolt if required.

Do not use lower grade hardware than specified.

Adjusting the Mower Deck

WARNING!

Before performing any service or adjustment checklist: 1. Engage the parking brake.

2.Place the Blade-switch in the disengaged position.

3.Turn ignition switch to “OFF” position and remove the key.

4.Make sure the blades and all moving parts have completely stopped.

5.Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug.

WARNING!

Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

Chech the tire pressure before adjustment of the mower deck, refer to page 41.

Faulty mower deck adjustment will cause an uneven mowing result.

46-English

Image 48
Contents Z18 EnglishPage Contents OPERATOR’S Manual Rider SeriesEnglish Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Passengers Safety Instructions Safety InstructionsGeneral Use Hearing Driving on Slopes Do as followsDo not Children Utility BoxMaintenance Risk of sparking Use protective glasses for maintenance work TransportCustomer responsibilities Controls ControlsControl Locations Motion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingIgnition Switch Choke ControlThrottle Control Hour Meter Parking BrakeMachine must be stopped before activating the parking brake Accessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual Battery To clean battery and terminalsReplacing battery Ignition System Checking the Safety System Checking and Adjusting Throttle Cable Checking the Engines Cooling Air IntakeReplacing the Air Filter Kohler engineInstall the cover and tighten the knobs by Faulty adjustment can cause an accident Replacing the Fuel FilterChecking Tire Pressures Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation EZT belt To replace EZT E-Series Zeroturn Transaxle beltEZT belt removal Always use protective gloves when handling the blades Checking the BladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingCaster Wheels HardwareLubrication Lubrication ScheduleLubricating the Cables Lubricating in Accordance with the Lubrication ScheduleCaster wheels Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Engine oil Kohler Changing the engine oil Changing the Oil Filter TransmissionTrouble Shooting Guide Trouble Shooting GuideProblem Cause Trouble Shooting Guide English-59 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZ18 Equipment Torque Specifications Conformity Certificates Conformity CertificatesService Journal Service JournalDelivery Service ActionAfter the First 5-8 Hours Hour Service English-69 Service Journal English-71 At Least Once Each Year Action Date, mtr reading, stamp, sign Service Journal English-75 ´z+RP¶6P¨ English-77 115 04 ´z+RP¶6P¨ ´z+RP¶6P¨