Husqvarna Z18 manual Oil drain valve

Page 55

LUBRICATION

1.Place the machine on a ﬂat surface.

2.Remove the yellow cap and ﬁt a hose to the drain valve.

3.Place a container under the engine where the hose from the oil drain valve exits.

4.Remove the dipstick and open the drain valve by turning and pulling out the black sleeve.

5.Allow the oil to run out into the container.

6.Then close the oil drain valve.

7.Remove hose and install the yellow cap. The cap must be installed to stop ﬂow if the valve is opened by mistake.

8.Replace the oil ﬁlter if necessary.

9.Fill with new engine oil in accordance with Checking the Oil Level.

10.Start the engine. Run it for a few seconds. Stop and re-check the oil level.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

8011-499

Oil drain valve

English-53

Image 55

Contents English Z18Page OPERATOR’S Manual Rider Series ContentsEnglish Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Passengers Safety Instructions Safety InstructionsGeneral Use Hearing Do as follows Driving on SlopesDo not Utility Box ChildrenMaintenance Risk of sparking Transport Use protective glasses for maintenance workCustomer responsibilities Controls ControlsControl Locations Tracking Motion Control LeversFuses Seat adjustment knobsBy pass linkages Refueling Blade switchChoke Control Ignition SwitchThrottle Control Parking Brake Hour MeterMachine must be stopped before activating the parking brake Cutting height pedal AccessoriesOperation OperationTraining Starting the Engine Before StartingDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual To clean battery and terminals BatteryReplacing battery Ignition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting Throttle CableKohler engine Replacing the Air FilterInstall the cover and tighten the knobs by Checking the Parking Brake Faulty adjustment can cause an accidentReplacing the Fuel Filter Checking Tire PressuresDeck belt Checking the V-beltsDeck belt installation To replace EZT E-Series Zeroturn Transaxle belt EZT beltEZT belt removal Checking the Blades Always use protective gloves when handling the bladesAdjusting the Mower Deck To level deck Side-to-side adjustmentFront-to-back adjustment To adjust anti-scalp rollers Hardware Cleaning and WashingUse protective glasses when cleaning and washing Caster WheelsLubrication Schedule LubricationEngine Oil Briggs & Stratton Changing the Engine Oil Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Caster wheelsOil drain valve Checking the oil level Engine oil Kohler Changing the engine oil Transmission Changing the Oil FilterTrouble Shooting Guide Trouble Shooting GuideProblem Cause Trouble Shooting Guide English-59 Winter Storage ServiceStorage StorageWiring diagram Wiring DiagramsTechnical Data Technical DataZ18 Equipment Torque Speciﬁcations Conformity Certiﬁcates Conformity CertificatesAction Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-69 Service Journal English-71 At Least Once Each Year Action Date, mtr reading, stamp, sign Service Journal English-75 ´z+RP¶6P¨ English-77 115 04 ´z+RP¶6P¨ ´z+RP¶6P¨