Husqvarna Z4818BIA/968999250 manual To adjust anti-scalp rollers

Page 53

MAINTENANCE

To adjust anti-scalp rollers

Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Anti-scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions.

IMPORTANT INFORMATION

Adjust Anti-scalp rollers with the mower on a flat level surface.

1.Adjust the deck to the desired cutting height (see “TO ADJUST DECK CUTTING HEIGHT” in the operation section of this manual).

2.Using a 3/4" wrench and a 9/16" wrench, remove the nut and shoulder bolt from the anti-scalp roller.

3.Lower the anti-scalp roller to the ground, and raise it up to the next highest hole.

4.Replace and tighten the nut and shoulder bolt.

5.Be sure to adjust all of the anti-scalp rollers to the same position.

6.Be sure to readjust the anti-scalp rollers if the cutting height is changed.

IMPORTANT INFORMATION

The anti-scalp rollers must not be used for gauge wheels or the roller and deck may be damaged.

Anti-scalp roller

CZ-9

English-51

Image 53
Contents Z4818BIA/968999250 Page OPERATOR’S Manual Rider English-2 Introduction IntroductionManufacturing Number Good ServiceXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Symbols and DecalsSymbols and Decals Greater Than Careful General Use Safety InstructionsSafety Instructions Hearing Do not Driving on SlopesDo as follows Children Maintenance Poisonous, and lethal gas Transport Use protective glasses for maintenance workCustomer responsibilities Control Locations ControlsParking Brake Tension Relief LeverTracking Motion Control LeversFuel Shut Off Valve Seat adjustment knobsRefueling Fuses By pass linkageChoke Control Ignition SwitchHour Meter Throttle Control Blade switchCutting height pedal AccessoriesTraining OperationOperation Starting the Engine Before StartingDepress the control for disengaging the mower deck Set the choke control USE Full Throttle When Mowing To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance Schedule MaintenanceMaintenance = Described in this manual  = Not described in this manua Replacing battery BatteryTo clean battery and terminals Ignition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Standard air filter Replacing the Air FilterChecking Tire Pressures Replacing the Fuel FilterChecking the Fuel Pump’s Air Filter Checking the Parking Brake Faulty adjustment can cause an accidentChecking the V-belts Deck beltDeck belt installation IZT belt Belt installationTo replace IZT Integraded Zeroturn Transaxle belt IZT belt removalChecking the Blades Always use protective gloves when handling the bladesRemove blade bolt by turning counterclockwise Adjusting the Mower Deck To level deck Side-to-side adjustmentFront-to-back adjustment To adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingRemoval and installation of caster wheel Caster WheelsTo adjust parking brake Tracking adjustmentParking brake Mower is tracking to the rightLubrication Schedule LubricationLubrication Lubricating in Accordance with the Lubrication Schedule Lubricating the CablesFront Wheel Mount Front Wheel BearingsEngine Oil Changing the Engine Oil Deck outer spindleChecking the Oil Level Transmission Changing the Oil FilterProblem Cause Trouble Shooting GuideTrouble Shooting Guide Water in the fuel English-61 Storage ServiceStorage Winter StorageWiring diagram Wiring DiagramsZ4818BIA Technical DataTechnical Data Productivity Torque Specifications AccessoriesUSA requirements Conformity CertificatesService Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 109797R0108/10/05