Husqvarna Z3815BIA, Z3815BIA, Z4217BIA, Z4218KOA, Z4218KOA manual Deck belt installation

Page 46

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt, refer to the routing decal on bottom of seat.

•Wrap the deck belt around the electric clutch pulley that is located on the engine shaft.

•Route the belt forward between the EZT (E-Series Zeroturn Transaxles) and up onto the deck.

•Place belt around spring loaded idler pulley, between the pulley and guide. Secure bolt and nut.

•Starting on the right hand side of the deck, wrap the belt around the stationary idler pulley, the right mandrel housing, then around to the left mandrel housing.

•Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt.

•Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed.

•Replace belt shields on both mandrel housings and secure with fasteners.

8011-773

1. Clutch pulley

Belt routing, deck belt

English-44

Image 46

Contents Operator´s manual Page Contents OPERATOR’S Manual Rider SeriesEnglish-2 Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Objects Engine is Running Moving sharp blades under cover Safety Instructions Safety InstructionsGeneral Use Hearing Do as follows Driving on SlopesDo not Children Utility BoxMaintenance Risk of sparking Use protective glasses for maintenance work TransportCustomer responsibilities Controls Control LocationsMotion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingChoke Control Ignition SwitchThrottle Control Parking Brake Hour MeterMachine must be stopped before activating the parking brake Accessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual To clean battery and terminals BatteryReplacing battery Ignition System Checking the Safety System Checking and Adjusting the Throttle Cable Checking the Engines Cooling Air IntakeReplacing the Air Filter Briggs and Stratton engineRemove the pre-cleaner Kohler engine Checking Tire Pressures Faulty adjustment can cause an accidentReplacing the Fuel Filter Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation To replace EZT E-Series Zeroturn Transaxle belt EZT beltEZT belt removal Always use protective gloves when handling the blades Checking the BladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Caster Wheels Cleaning and WashingUse protective glasses when cleaning and washing HardwareLubrication LubricationLubrication Schedule Caster wheels Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Engine oil Kohler Changing the engine oil Changing the Oil Filter TransmissionTrouble Shooting Guide Trouble Shooting GuideProblem Cause Water in the fuel English-60 Storage ServiceStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZ3815 Z4218 Z4217 Equipment Torque Specifications Conformity Certificates USA requirementsDelivery Service Service JournalService Journal Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-70 English-71 English-72 At Least Once Each Year Action111826R0211/29/05