Husqvarna Z3815BIA, Z3815BIA, Z4217BIA, Z4218KOA, Z4218KOA manual EZT belt removal

Page 47

MAINTENANCE

EZT belt

To replace EZT (E-Series Zeroturn

Transaxle) belt

Park the mower on a level surface. Engage the parking brake.

EZT belt removal

NOTE: Be careful not to damage the fan blades on the EZT´s as this can affect cooling or damage the EZT´s

•Remove the deck belt (see to replace deck belt in this section of the manual).

•Unplug clutch from wiring harness.

Remove bolt from center of clutch and slide clutch off of engine shaft.

•Create slack in the belt by removing the spring on the pump idler arm.

•The belt should now be able to be removed from the engine pulley and EZT pulleys.

Belt installation

Transaxle belt

•Wrap the EZT belt around the EZT pulleys

•Route the belt around the inside of the idler pulley.

•Now you can wrap the belt around the engine pulley.

•Reattach the spring on the pump idler arm.

•Install clutch on to engine shaft (pulley side down) make sure key is installed and align the clutch anti rotation tab into slot on clutch. Secure clutch, install wire.

•Reinstall the deck belt onto the electric clutch belt (see to replace deck belt in this section of the manual).

English-45

Image 47

Contents Operator´s manual Page OPERATOR’S Manual Rider Series ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Symbols and DecalsSymbols and Decals Objects Engine is Running Moving sharp blades under cover General Use Safety InstructionsSafety Instructions Hearing Do not Driving on SlopesDo as follows Utility Box ChildrenMaintenance Risk of sparking Transport Use protective glasses for maintenance workCustomer responsibilities Control Locations ControlsTracking Motion Control LeversFuses Seat adjustment knobsBy pass linkages Refueling Blade switchThrottle Control Ignition SwitchChoke Control Machine must be stopped before activating the parking brake Hour MeterParking Brake Cutting height pedal AccessoriesTraining OperationOperation Starting the Engine Before StartingDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance Schedule MaintenanceMaintenance = Described in this manual = Not described in this manual Replacing battery BatteryTo clean battery and terminals Ignition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableBriggs and Stratton engine Replacing the Air FilterRemove the pre-cleaner Kohler engine Checking the Parking Brake Faulty adjustment can cause an accidentReplacing the Fuel Filter Checking Tire PressuresDeck belt Checking the V-beltsDeck belt installation EZT belt removal EZT beltTo replace EZT E-Series Zeroturn Transaxle belt Checking the Blades Always use protective gloves when handling the bladesAdjusting the Mower Deck To level deck Side-to-side adjustmentFront-to-back adjustment To adjust anti-scalp rollers Hardware Cleaning and WashingUse protective glasses when cleaning and washing Caster WheelsLubrication Schedule LubricationLubrication Engine Oil Briggs & Stratton Changing the Engine Oil Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Caster wheelsOil drain valve Checking the oil level Engine oil Kohler Changing the engine oil Transmission Changing the Oil FilterProblem Cause Trouble Shooting GuideTrouble Shooting Guide Water in the fuel English-60 Winter Storage ServiceStorage StorageWiring diagram Wiring DiagramsZ3815 Z4218 Z4217 Technical DataTechnical Data Equipment Torque Specifications USA requirements Conformity CertificatesAction Date, mtr reading, stamp, sign Service JournalService Journal Delivery ServiceAfter the First 5-8 Hours Hour Service English-70 English-71 English-72 Action At Least Once Each Year111826R0211/29/05