Husqvarna Z3815BIA, Z3815BIA, Z4217BIA, Z4218KOA, Z4218KOA manual

Page 58

LUBRICATION

2.Engine oil (Kohler) Changing the engine oil

The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it should be changed every 50 hours.

WARNING!

Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first.

1.Place the machine on a flat surface.

2.Place a container under the engine where the oil drain exits.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

8011-740

Oil drain plug Kohler

3.Remove the dipstick and open the drain plug.

4.Allow the oil to run out into the container.

5.Install and tighten the oil drain plug.

6.Replace the oil filter if necessary.

7. Fill with new engine oil in accordance with Checking the Oil Level.

8. Start the engine. Run it for a few seconds and re-check the oil level.

8011-741

Dipstick

English-56

Image 58

Contents Operator´s manual Page Contents OPERATOR’S Manual Rider SeriesEnglish-2 Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Objects Engine is Running Moving sharp blades under cover Safety Instructions Safety InstructionsGeneral Use Hearing Do as follows Driving on SlopesDo not Children Utility BoxMaintenance Risk of sparking Use protective glasses for maintenance work TransportCustomer responsibilities Controls Control LocationsMotion Control Levers TrackingSeat adjustment knobs FusesBy pass linkages Blade switch RefuelingChoke Control Ignition SwitchThrottle Control Parking Brake Hour MeterMachine must be stopped before activating the parking brake Accessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDisengage the mower blades by depressing the blade switch Press in and turn the ignition key to the start position To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual To clean battery and terminals BatteryReplacing battery Ignition System Checking the Safety System Checking and Adjusting the Throttle Cable Checking the Engines Cooling Air IntakeReplacing the Air Filter Briggs and Stratton engineRemove the pre-cleaner Kohler engine Checking Tire Pressures Faulty adjustment can cause an accidentReplacing the Fuel Filter Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation To replace EZT E-Series Zeroturn Transaxle belt EZT beltEZT belt removal Always use protective gloves when handling the blades Checking the BladesAdjusting the Mower Deck Side-to-side adjustment To level deckFront-to-back adjustment To adjust anti-scalp rollers Caster Wheels Cleaning and WashingUse protective glasses when cleaning and washing HardwareLubrication LubricationLubrication Schedule Caster wheels Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Checking the oil level Engine oil Kohler Changing the engine oil Changing the Oil Filter TransmissionTrouble Shooting Guide Trouble Shooting GuideProblem Cause Water in the fuel English-60 Storage ServiceStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZ3815 Z4218 Z4217 Equipment Torque Specifications Conformity Certificates USA requirementsDelivery Service Service JournalService Journal Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-70 English-71 English-72 At Least Once Each Year Action111826R0211/29/05