Husqvarna CTH151 owner manual To Operate Mower See Fig, To Operate on Hills, To Transport See Figs

Page 14

OPERATION

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

3/8-16 LOCKNUT

GAUGE WHEEL

MOUNTING BRACKET

3/8 WASHER

GAUGE WHEEL

SHOULDER BOLT

FIG. 11

TO OPERATE MOWER (See Fig. 12)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "ENGAGED"

POSITION

"DISENGAGED" POSITION

02381

FIG. 12

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 9 and 13)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located under the seat.

•Raise attachment lift to highest position with attachment lift control.

•Raise seat and pull freewheel control up and back into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

02219

Transmission Disengaged

FIG. 13

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents CTH151 General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat BatteryUnassembled Parts KeyHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsVertical Adjustment Bagger Adjustment See FigHorizontal Adjustment To Assemble and Install Mulcher Plug See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMulching Mowing Tips Mowing TipsPurge Transmission Bagging see Fig To Dump Bagger SeeTo Convert Mower See Fig General Recommendations MaintenanceLubrication Chart Before Each USETires TractorBrake Operation Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Adjust Carburetor To Adjust Steering Wheel AlignmentTo Adjust Throttle Control Cable Front Wheel TOE-IN/CAMBERFuel System StorageOther Engine OILTroubleshooting Points When operator leaves seat Schematic TRACTOR- -MODEL NO. CTH151 HAUCT15HK36A, Product no 17Electrical KEY Part Description Chassis and Enclosures 261Repair Parts Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 117 532 18 Tube Exhaust Mower Lift 532 15 94-60 Washer Asm Inner Spring W/Plunger Mower CRD SVCBagger 532 17 Plug Tubing EndWarranty Statement Suggested Guide for Sighting Slopes for Safe Operation

CTH151 specifications

The Husqvarna CTH151 is a standout in the realm of lawn care, designed to deliver exceptional performance, reliability, and ease of use. This compact tractor combines advanced technology with practical features, making it a fitting choice for both residential and commercial landscaping tasks.

One of the defining features of the CTH151 is its robust engine. Powered by a reliable Briggs & Stratton engine, the tractor ensures ample power for tackling various mowing conditions. This engine is designed for durability and easy starting, providing peace of mind for users who depend on their equipment for consistent performance.

The CTH151 boasts a cutting deck size of 42 inches, allowing it to efficiently manage medium to large mowing areas. The deck’s design optimizes grass dispersion, resulting in a clean and uniform cut. Furthermore, the cutting height can be easily adjusted to suit different grass types and seasonal changes, providing flexibility for any lawn care routine.

The innovative Dual Hydrostatic transmission system of the CTH151 allows for smooth and precise control, enabling the operator to navigate through tight spaces and around obstacles with ease. This feature is especially beneficial for those with intricately landscaped yards. With its zero-turn capability, users can expect improved maneuverability, reducing the need for trimming and enhancing overall mowing efficiency.

Ergonomics play a crucial role in the design of the Husqvarna CTH151. The comfortable seat and intuitive controls allow for extended periods of use without fatigue. The dashboard features clear indicators and easy-to-reach controls, making the tractor user-friendly for both seasoned operators and newcomers alike.

Safety is a priority with the CTH151, equipped with features like an automatic blade brake and a seat switch that stops the engine when the operator leaves the seat. These features enhance the overall safety of the tractor, providing reassurance while performing yard tasks.

In terms of maintenance, the CTH151 is designed with accessibility in mind. Oil changes and blade replacements can be carried out with minimal effort, making upkeep straightforward and manageable.

Overall, the Husqvarna CTH151 combines power, efficiency, and user-friendly features, establishing itself as an invaluable tool for anyone serious about maintaining a pristine lawn. With its thoughtful design and advanced technologies, it ensures that grass cutting is not just a chore, but an enjoyable and satisfying experience.
Top Page Image Contents