Husqvarna CTH151 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 22

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSMENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 24)

Mower will be easier to remove from the right side of tractor.

•Place attachment clutch control in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off clutch pulley.

•Disconnect anti-sway bar from chassis bracket by removing retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower

out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHERTHANTHE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS.

TO INSTALL MOWER (See Fig. 24)

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake.

•Slide mower under tractor.

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Install belt into clutch pulley groove.

•Install left front link into the left hand front mower bracket (retain with single loop retainer springs as shown).

•Slide right side of mower back and install right front link into right hand front mower bracket (retain with single loop retainer springs).

•Place the suspension arms on mower pins, if necessary, rock and raise front of mower to align mower pins with the holes in suspension arms. Retain with double loop retainer spring, loop down as shown.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Makesuretiresareproperlyinflated(See“PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 25 and 26)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

BOTTOM EDGE

00598

BOTTOM EDGE

OF MOWER

OF MOWER

 

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

 

FIG. 25

 

RETAINER SPRING

CLUTCH PULLEY

SUSPENTION

 

ARMS

 

 

FRONT LINKS

RETAINER SPRING

RETAINER SPRINGS

ANTI SWAY

BAR

FIG. 24

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents CTH151 General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat BatteryUnassembled Parts KeyHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsVertical Adjustment Bagger Adjustment See FigHorizontal Adjustment To Assemble and Install Mulcher Plug See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigTo Transport See Figs ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigPurge Transmission Mowing TipsMulching Mowing Tips To Convert Mower See Fig To Dump Bagger SeeBagging see Fig General Recommendations MaintenanceLubrication Chart Before Each USETires TractorBrake Operation Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig To Adjust Carburetor To Adjust Steering Wheel AlignmentTo Adjust Throttle Control Cable Front Wheel TOE-IN/CAMBERFuel System StorageOther Engine OILTroubleshooting Points When operator leaves seat Schematic TRACTOR- -MODEL NO. CTH151 HAUCT15HK36A, Product no 17Electrical KEY Part Description Chassis and Enclosures 261Repair Parts Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 117 532 18 Tube Exhaust Mower Lift 532 15 94-60 Washer Asm Inner Spring W/Plunger Mower CRD SVCBagger 532 17 Plug Tubing EndWarranty Statement Suggested Guide for Sighting Slopes for Safe Operation

CTH151 specifications

The Husqvarna CTH151 is a standout in the realm of lawn care, designed to deliver exceptional performance, reliability, and ease of use. This compact tractor combines advanced technology with practical features, making it a fitting choice for both residential and commercial landscaping tasks.

One of the defining features of the CTH151 is its robust engine. Powered by a reliable Briggs & Stratton engine, the tractor ensures ample power for tackling various mowing conditions. This engine is designed for durability and easy starting, providing peace of mind for users who depend on their equipment for consistent performance.

The CTH151 boasts a cutting deck size of 42 inches, allowing it to efficiently manage medium to large mowing areas. The deck’s design optimizes grass dispersion, resulting in a clean and uniform cut. Furthermore, the cutting height can be easily adjusted to suit different grass types and seasonal changes, providing flexibility for any lawn care routine.

The innovative Dual Hydrostatic transmission system of the CTH151 allows for smooth and precise control, enabling the operator to navigate through tight spaces and around obstacles with ease. This feature is especially beneficial for those with intricately landscaped yards. With its zero-turn capability, users can expect improved maneuverability, reducing the need for trimming and enhancing overall mowing efficiency.

Ergonomics play a crucial role in the design of the Husqvarna CTH151. The comfortable seat and intuitive controls allow for extended periods of use without fatigue. The dashboard features clear indicators and easy-to-reach controls, making the tractor user-friendly for both seasoned operators and newcomers alike.

Safety is a priority with the CTH151, equipped with features like an automatic blade brake and a seat switch that stops the engine when the operator leaves the seat. These features enhance the overall safety of the tractor, providing reassurance while performing yard tasks.

In terms of maintenance, the CTH151 is designed with accessibility in mind. Oil changes and blade replacements can be carried out with minimal effort, making upkeep straightforward and manageable.

Overall, the Husqvarna CTH151 combines power, efficiency, and user-friendly features, establishing itself as an invaluable tool for anyone serious about maintaining a pristine lawn. With its thoughtful design and advanced technologies, it ensures that grass cutting is not just a chore, but an enjoyable and satisfying experience.
Top Page Image Contents