Husqvarna CTH151 owner manual Engine

Page 20

MAINTENANCE

BLADE REMOVAL

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove battery cover.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “CONNECT BATTERY” in the Assembly section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos- sible damage to seals, do not use high pressure water or steam to clean transaxle.

•Inspect cooling fan to be sure fan blades are intact and clean.

•Inspect cooling fins for dirt, grass clippings and other materials.To prevent damage to seals, do not use com- pressed air or high pressure sprayer to clean cooling fins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid mainte- nance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

10W30

 

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

 

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart4_e

Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation.

TO CHANGE ENGINE OIL (See Fig. 22)

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

 

OIL DRAIN VALVE

 

 

CLOSED

 

 

63

 

4

2

 

AND

0

 

 

 

 

 

LOCKED

 

 

 

POSITION

 

 

 

YELLOW

 

 

 

CAP

 

 

DRAIN

 

 

 

 

 

 

TUBE

FIG. 22

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents CTH151 Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Battery Unassembled PartsSteering Wheel Seat KeyAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsBagger Adjustment See Fig Horizontal AdjustmentVertical Adjustment To Assemble and Install Mulcher Plug See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsPurge Transmission Bagging see Fig To Dump Bagger SeeTo Convert Mower See Fig Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Adjust Steering Wheel Alignment To Adjust Throttle Control CableTo Adjust Carburetor Front Wheel TOE-IN/CAMBERStorage OtherFuel System Engine OILTroubleshooting Points When operator leaves seat Schematic TRACTOR- -MODEL NO. CTH151 HAUCT15HK36A, Product no 17Electrical KEY Part Description Chassis and Enclosures 261Repair Parts Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 117 532 18 Tube Exhaust Mower Lift 532 15 94-60 Washer Asm Inner Spring W/Plunger Mower CRD SVCBagger 532 17 Plug Tubing EndWarranty Statement Suggested Guide for Sighting Slopes for Safe Operation

CTH151 specifications

The Husqvarna CTH151 is a standout in the realm of lawn care, designed to deliver exceptional performance, reliability, and ease of use. This compact tractor combines advanced technology with practical features, making it a fitting choice for both residential and commercial landscaping tasks.

One of the defining features of the CTH151 is its robust engine. Powered by a reliable Briggs & Stratton engine, the tractor ensures ample power for tackling various mowing conditions. This engine is designed for durability and easy starting, providing peace of mind for users who depend on their equipment for consistent performance.

The CTH151 boasts a cutting deck size of 42 inches, allowing it to efficiently manage medium to large mowing areas. The deck’s design optimizes grass dispersion, resulting in a clean and uniform cut. Furthermore, the cutting height can be easily adjusted to suit different grass types and seasonal changes, providing flexibility for any lawn care routine.

The innovative Dual Hydrostatic transmission system of the CTH151 allows for smooth and precise control, enabling the operator to navigate through tight spaces and around obstacles with ease. This feature is especially beneficial for those with intricately landscaped yards. With its zero-turn capability, users can expect improved maneuverability, reducing the need for trimming and enhancing overall mowing efficiency.

Ergonomics play a crucial role in the design of the Husqvarna CTH151. The comfortable seat and intuitive controls allow for extended periods of use without fatigue. The dashboard features clear indicators and easy-to-reach controls, making the tractor user-friendly for both seasoned operators and newcomers alike.

Safety is a priority with the CTH151, equipped with features like an automatic blade brake and a seat switch that stops the engine when the operator leaves the seat. These features enhance the overall safety of the tractor, providing reassurance while performing yard tasks.

In terms of maintenance, the CTH151 is designed with accessibility in mind. Oil changes and blade replacements can be carried out with minimal effort, making upkeep straightforward and manageable.

Overall, the Husqvarna CTH151 combines power, efficiency, and user-friendly features, establishing itself as an invaluable tool for anyone serious about maintaining a pristine lawn. With its thoughtful design and advanced technologies, it ensures that grass cutting is not just a chore, but an enjoyable and satisfying experience.
Top Page Image Contents