Husqvarna CTH151 owner manual To Install Bagger Components to Tractor See Figs A-4D

Page 8

ASSEMBLY

Start the engine.After engine has started, move throttle control to idle position.

Release parking brake.

Slowly move the motion control lever forward and slowly drive tractor off skid.

Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

Turn ignition key to "OFF" position.

Continue with the instructions that follow.

TO INSTALL BAGGER COMPONENTS TO TRACTOR (See Figs. 4A-4D)

Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor.

Remove the two (2) 3/8 nuts and flat washers from the bolts at the tractor back plate.

DISCHARGE

CHUTE

3/8 NUT

FLATWASHER

0 2277

FIG. 4A

Using the nuts and flat washers removed from tractor back plate, install the bagger support tube to the back plate as shown. Tighten securely.

SUPPORT

TUBE

FLAT

WASHER

3/8 NUT

BOLT

02330

 

FIG. 4B

Install the two upper support brackets through the back plate and to the chassis, using the 10 x 19 mm (3/8"x3/4") carriage bolts and locknuts supplied.Tighten securely.

Assemble both support brackets to the outside of the baggger support tube using two each 3/8 x 63,5mm hex bolts13/32" I.D. flat washers and 3/8 locknuts from parts bag. Tighten securely.

Replace discharge chute into rear opening of tractor. Secure the chute with the two hook straps.

3/8 LOCK NUT

3/8 LOCK NUT

SUPPORT BRACKET

13/32 FLAT WASHER

3/8 HEX BOLT

3/8 CARRIAGE BOLT

02590

 

FIG. 4C

NOTE:The strap hook must go through the discharge chute only. Do not allow the hook to enter the slot in the tractor back plate.This will allow the discharge chute to float with the mower deck when moving on uneven terrain.

DISCHARGE

CHUTE

 

HOOK

02306

BACKPLATE

SLOT

FIG. 4D

TO ASSEMBLE BAGGER (See Figs. 5 & 6)

NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together.

Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts.

Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely.

FRONT BAGGER TUBE

LOWER

BAGGER

 

 

 

 

TUBE

1/4 X 2"

 

 

CARRIAGE

1/4 LOCK

 

BOLTS

2

NUT

0259

 

 

FIG. 5

Slide front and lower bagger tube assembly into the bagger assemby.

Assemble front and upper bagger tubes using four (4) 1/4 x 50,8mm carraige bolts and lock nuts supplied. Tighten securely.

8

Image 8
Contents CTH151 Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Battery Unassembled PartsSteering Wheel Seat KeyAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsBagger Adjustment See Fig Horizontal AdjustmentVertical Adjustment To Assemble and Install Mulcher Plug See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsPurge Transmission Bagging see Fig To Dump Bagger SeeTo Convert Mower See Fig Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Adjust Steering Wheel Alignment To Adjust Throttle Control CableTo Adjust Carburetor Front Wheel TOE-IN/CAMBERStorage OtherFuel System Engine OILTroubleshooting Points When operator leaves seat Schematic TRACTOR- -MODEL NO. CTH151 HAUCT15HK36A, Product no 17Electrical KEY Part Description Chassis and Enclosures 261Repair Parts Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 117 532 18 Tube Exhaust Mower Lift 532 15 94-60 Washer Asm Inner Spring W/Plunger Mower CRD SVCBagger 532 17 Plug Tubing EndWarranty Statement Suggested Guide for Sighting Slopes for Safe Operation

CTH151 specifications

The Husqvarna CTH151 is a standout in the realm of lawn care, designed to deliver exceptional performance, reliability, and ease of use. This compact tractor combines advanced technology with practical features, making it a fitting choice for both residential and commercial landscaping tasks.

One of the defining features of the CTH151 is its robust engine. Powered by a reliable Briggs & Stratton engine, the tractor ensures ample power for tackling various mowing conditions. This engine is designed for durability and easy starting, providing peace of mind for users who depend on their equipment for consistent performance.

The CTH151 boasts a cutting deck size of 42 inches, allowing it to efficiently manage medium to large mowing areas. The deck’s design optimizes grass dispersion, resulting in a clean and uniform cut. Furthermore, the cutting height can be easily adjusted to suit different grass types and seasonal changes, providing flexibility for any lawn care routine.

The innovative Dual Hydrostatic transmission system of the CTH151 allows for smooth and precise control, enabling the operator to navigate through tight spaces and around obstacles with ease. This feature is especially beneficial for those with intricately landscaped yards. With its zero-turn capability, users can expect improved maneuverability, reducing the need for trimming and enhancing overall mowing efficiency.

Ergonomics play a crucial role in the design of the Husqvarna CTH151. The comfortable seat and intuitive controls allow for extended periods of use without fatigue. The dashboard features clear indicators and easy-to-reach controls, making the tractor user-friendly for both seasoned operators and newcomers alike.

Safety is a priority with the CTH151, equipped with features like an automatic blade brake and a seat switch that stops the engine when the operator leaves the seat. These features enhance the overall safety of the tractor, providing reassurance while performing yard tasks.

In terms of maintenance, the CTH151 is designed with accessibility in mind. Oil changes and blade replacements can be carried out with minimal effort, making upkeep straightforward and manageable.

Overall, the Husqvarna CTH151 combines power, efficiency, and user-friendly features, establishing itself as an invaluable tool for anyone serious about maintaining a pristine lawn. With its thoughtful design and advanced technologies, it ensures that grass cutting is not just a chore, but an enjoyable and satisfying experience.