Husqvarna CTH151 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Utility knife

(1)

3/4" wrenches

Tire pressure gauge

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

WHEEL

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ADAPTER

STEERING

BOOT

TABS

EXTENSION SHAFT

1/4 HEX BOLT

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 1/2 hex nut and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

1/4 LOCKNUT

LOWER

TAB

STEERING

SHAFT

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CONNECT BATTERY (See Figs. 2)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions).

6

Image 6
Contents CTH151 General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat BatteryUnassembled Parts KeyHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Install Bagger Components to Tractor See Figs A-4D To Assemble Bagger See FigsVertical Adjustment Bagger Adjustment See FigHorizontal Adjustment To Assemble and Install Mulcher Plug See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionMulching Mowing Tips To Dump Bagger See To Convert Mower See FigBagging see Fig General Recommendations MaintenanceLubrication Chart Before Each USETires TractorBrake Operation Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral ADJUSTMENTSee FigTo Replace Motion Drive Belt See Fig To Adjust Carburetor To Adjust Steering Wheel AlignmentTo Adjust Throttle Control Cable Front Wheel TOE-IN/CAMBERFuel System StorageOther Engine OILTroubleshooting Points When operator leaves seat Schematic TRACTOR- -MODEL NO. CTH151 HAUCT15HK36A, Product no 17Electrical KEY Part Description Chassis and Enclosures 261Repair Parts Drive Repair Parts Steering Assembly 532 16 Steering Wheel Seat Assembly 532 18 SeatDecals Wheels & TiresEngine 117 532 18 Tube Exhaust Mower Lift 532 15 94-60 Washer Asm Inner Spring W/Plunger Mower CRD SVCBagger 532 17 Plug Tubing EndWarranty Statement Suggested Guide for Sighting Slopes for Safe Operation

CTH151 specifications

The Husqvarna CTH151 is a standout in the realm of lawn care, designed to deliver exceptional performance, reliability, and ease of use. This compact tractor combines advanced technology with practical features, making it a fitting choice for both residential and commercial landscaping tasks.

One of the defining features of the CTH151 is its robust engine. Powered by a reliable Briggs & Stratton engine, the tractor ensures ample power for tackling various mowing conditions. This engine is designed for durability and easy starting, providing peace of mind for users who depend on their equipment for consistent performance.

The CTH151 boasts a cutting deck size of 42 inches, allowing it to efficiently manage medium to large mowing areas. The deck’s design optimizes grass dispersion, resulting in a clean and uniform cut. Furthermore, the cutting height can be easily adjusted to suit different grass types and seasonal changes, providing flexibility for any lawn care routine.

The innovative Dual Hydrostatic transmission system of the CTH151 allows for smooth and precise control, enabling the operator to navigate through tight spaces and around obstacles with ease. This feature is especially beneficial for those with intricately landscaped yards. With its zero-turn capability, users can expect improved maneuverability, reducing the need for trimming and enhancing overall mowing efficiency.

Ergonomics play a crucial role in the design of the Husqvarna CTH151. The comfortable seat and intuitive controls allow for extended periods of use without fatigue. The dashboard features clear indicators and easy-to-reach controls, making the tractor user-friendly for both seasoned operators and newcomers alike.

Safety is a priority with the CTH151, equipped with features like an automatic blade brake and a seat switch that stops the engine when the operator leaves the seat. These features enhance the overall safety of the tractor, providing reassurance while performing yard tasks.

In terms of maintenance, the CTH151 is designed with accessibility in mind. Oil changes and blade replacements can be carried out with minimal effort, making upkeep straightforward and manageable.

Overall, the Husqvarna CTH151 combines power, efficiency, and user-friendly features, establishing itself as an invaluable tool for anyone serious about maintaining a pristine lawn. With its thoughtful design and advanced technologies, it ensures that grass cutting is not just a chore, but an enjoyable and satisfying experience.