Philips PM2812 manuals

115 pages485.39 Kb

PM2811-PM2812-PM2813
PM2831-PM2832
- Users Manual
  - Pro
  - rammable Power Supplies III
  - 3LIMITED WARRANTY & LIMITATION OF LIABILITY
  - 5CONTENS
    - 1 OPERATOR SAFETY
    - 2 INTRODUCTION
    - 63 INSTALLATION INSTRUCTIONS
    - 4 GETTING FAMILIAR WITH THE POWER SUPPLY
    - 75 USING YOUR PROGRAMMABLE POWER SUPPLY
  - 11INSIDE THIS MANUAL
- 131 OPERATOR SAFETY
  - 1.1 INTRODUCTION
  - 1.2 SAFETY PRECAUTIONS
  - 1.3 CAUTION AND WARNING STATEMENTS
    - CAUTION: Is used to indicate correct operatin
    - or maintenance procedures in order to prevent dama
    - e to or destruction of the equipment or other property.
  - 141.4 SYMBOLS
  - 1.5 IMPAIRED SAFETY
- 152 INTRODUCTION
  - 2.1 INTRODUCTION TO YOUR PROGRAMMABLE POWER SUPPLY
    - !
    - 17Single rear panel (PM2811 only)
      - !!!
      - -S -V +V +S -S -V +V +S
        READY
        START
      - IEEE488
        ST5825
        READY
        START
      - IEEE488
      - OUTPUT1 30V10A 60W -S -V +V +S
        1
        MAX 240V !
        FUSES 110V2.5AT/250V 220V1.25AT/250V
        PM2811/111 944802811011 No.DM000599
        230V 50-60Hz 155VA
        0
      - !
        OUTPUT1
        OUTPUT2
        OUTPUT3
        -S -V +V +S
        01
    - Output rear panel
  - 182.2 BASIC OPERATION
    - 21IEEE 488.2 compatibility
    - SCPI compatibility
  - 262.3 ADVANCED OPERATION
- 293 INSTALLATION INSTRUCTIONS
  - 3.1 INTRODUCTION
  - 3.2 INITIAL INSPECTION
  - 3.3 OPERATOR SAFETY INSTRUCTIONS
    - CAUTION: When an instrument is brou
    - roundin
    - requirements are strictly adhered to.
  - 303.4 INSTALLATION
    - 32Note: Switchin
  - 353.5 OUTPUT CONNECTIONS
  - 373.6 ACCEPTANCE TESTS
    - 39Note: For meanin
    - es" in the Reference Manual.
    - of the hardware error numbers, refer to section 3.6.1 "Brief check" or to "Error Messa
- 414 GETTING FAMILIAR WITH THE POWER SUPPLY
  - 4.1 INITIAL SETUP OF YOUR POWER SUPPLY
    - Normal self test indications
    - Self test errors
    - 42Note: The address aa is the actual GPIB device address (default = 28).
    - Note: The SELECT function is applicable only for multiple output models.
  - 434.2 FRONT PANEL LAYOUT
    - .
      - 444 - 4 Users Manual
        +
      - 45Gettin
      - Familair with the Power Supply 4 - 5
      - 1) The CALIBRATION mode is entered when you turn on the power supply while pressin
      - the AUX key. 2) To unlock the keyboard, press the ENTER key for approximately 5 seconds.
      - 46Note: The output channel indication is displayed only for multiple output channel models.
  - 474.3 OUTPUT CHANNEL CONNECTIONS
  - 484.4 GETTING STARTED
    - le output model the number n will not be displayed.
    - 50Note: The diameter of the jumper wire must be lar
    - e enou
    - h to carry the maximum short-circuit current.
- 535 USING YOUR PROGRAMMABLE POWER SUPPLY
  - 5.1 INTRODUCTION
  - 545.2 LOCAL OPERATION
    - = applies to multiple output models only.
    - Note:
  - 555.3 REMOTE OPERATION
  - 565.4 OPERATING FEATURES
    - 58CAUTION: Only output channels with equivalent volta
    - e and current ratin
    - ed.
    - s may be connected in series or in parallel to prevent that the channel with the lowest ratin
    - s will be dama
  - 595.5 HOW TO USE THE OPERATING FEATURES
    - PM2811/12/13
    - ure 5.5.1 Output Channel Characteristics
    - 60PM2831/32
    - ure 5.5.2 Output channel characteristics
    - 61ure 5.5.3 Current sink characteristics
    - 62.
    - any chan
    - ure 5.5.4 Volta
    - e drop due to Wire Resistance R
    - 63 mode:
    - Remote sensin
    - ure 5.5.6 Connection of a Load in the Remote Sense Mode
    - mode:
    - ure 5.5.5 Connection of a Load in the Local Sense Mode
    - 65ure 5.5.7 Power Output Crossover Point
    - 69Local control (in CV or CC mode):
    - 70Remote control (in CV or CC mode):
    - 72Note: To remember which locations have been pro
    - rammed and which have not, keep a record (such as the followin
    - ) of which locations have been used.
    - Local control (store/recall):
    - 73Remote control (store/recall):
    - 74Manual step function:
    - 75Remark: When the next step is executed, the next volta
    - e and current settin
    - ):
    - 77Remote control (automatic steppin
    - ):
    - 78External step functions
    - 79Note: LOW = 0 to 0.8V and HIGH = 2 to 5V Tri
    - gg
    - er bus control:
    - nored.
    - Note: STEP pulses, received while the READY line is low, will be i
  - 805.6 ADVANCED USE
    - 81Note: For the PM2812 and PM2813 you can face a number of restrictions when connectin
    - output channels in parallel to a load. Please read Appendix D to
    - 82 (outputs in parallel):
    - with Two Outputs in Parallel
    - CAUTION: To prevent noise pickup, twist the sense wires and shield them from the environment.
    - ure 5.6.1 Local Sensin
    - 87DT+ DT
      - 88Remote sensin
      - (loads in parallel):
      - CAUTION: To prevent noise pickup, twist the sense wires and shield them from the environment.
      - ure 5.6.6 Remote Sensin
      - withTwo Loads in Parallel
- 89APPENDIX A ACCESSORIES
  - A.1 Supplied with the instrument
  - A.2 Optional
- 91APPENDIX B SCPI CONFORMANCE INFORMATION
  - 94B.3 SCPI approved
  - 95B.4 SCPI syntax and style
- 97APPENDIX C ABBREVIATIONS, SYMBOLS & TERMS
  - C.1 Abbreviations
  - 101C.2 Glossary of symbols
  - 102C.3 Glossary of terms
- 105APPENDIX D APPLICATION FOR PM2812 AND PM2813
  - e mode.
  - 106ure D.2 Channels connected in parallel to a load. Both channels are in Constant Volta
  - e mode.
  - 107Note: Coupled Protection is possible only for the channels in the same Power Supply.
  - Try to prevent that the down pro
  - Case 1: Constant Current
  - 108Case 2: Constant Volta
  - e, Output Current from a fixed minimum value to the maximum
  - 109Case 3: Constant Volta
  - e, Output Current from 0A to the maximum
- 111INDEX
  - A
  - C
  - D
  - 112E
  - F
  - G
  - I
  - 113L
  - M
  - N
  - O
  - P
  - 114R
  - S
  - 115T
  - V
  - W