Philips PM2811, PM2812, PM2813, PM2831, PM2832 5.2 LOCAL OPERATION

5 - 2 Users Manual

5.2 LOCAL OPERATION

Local operation of your power supply is done throu

g

h the front panel keys and

display. Operational and error information is shown on the display. The keys are

used for operator communication and have been placed into functional

g

roups.

This makes the functional use of the power supply very easy:

• OUTPUT control : control over the output channels

• SET output : settin

g

a channel output

• FAULT handlin

g

: fault handlin

g

per output channel

• output adjustment : adjustin

g

a channel output

• numeric control : input of fi

g

ures or special keys

• instrument control : control over the instrument

reset reset the power supply

OPR/STBY set OPERATE or STANDBY mode

OUTPUT control SELECT select output channel *

ENABLE/DISABLE enable/disable output channel *

V set output volta

g

e

I set output current

SET output OVP set overvolta

g

e protection trip level

OCP EN/OCP DIS enable/disable overcurrent

protection

DELAY verify/set repro

g

rammin

g

delay

RESET reset protection circuits

FAULT handlin

g

UNMASK verify/set fault mask

DISP display fault re

g

ister

- V + adjust output volta

g

e

output adjustment - I + adjust output current

0 (OFF)

fi

g

ures 1 (ON)

2 ... 9

numeric control (backspace)

specials ENTER

• (dot)

LCL

g

ain local control

AUX perform system functions

instrument control STORE store volta

g

e/current settin

g

s

RECALL recall volta

g

e/current settin

g

s

STEP step throu

g

h volta

g

e/current settin

g

s

W

Note:

*

= applies to multiple output models only.

Contents

Main PM2811-PM2812-PM2813 PM2831-PM2832 Users Manual Page Pro rammable Power Supplies III LIMITED WARRANTY & LIMITATION OF LIABILITY Page CONTENS 1 OPERATOR SAFETY 2 INTRODUCTION 3 INSTALLATION INSTRUCTIONS 4 GETTING FAMILIAR WITH THE POWER SUPPLY 5 USING YOUR PROGRAMMABLE POWER SUPPLY Page Page Page INSIDE THIS MANUAL Page 1 OPERATOR SAFETY 1.1 INTRODUCTION 1.2 SAFETY PRECAUTIONS 1.3 CAUTION AND WARNING STATEMENTS CAUTION: Is used to indicate correct operatin 1.4 SYMBOLS 1.5 IMPAIRED SAFETY 2 INTRODUCTION 2.1 INTRODUCTION TO YOUR PROGRAMMABLE POWER SUPPLY Page ! Single rear panel (PM2811 only) !!! -S -V +V +S -S -V +V +S READY START 2.2 BASIC OPERATION Page Page IEEE 488.2 compatibility SCPI compatibility Page Page Page Page 2.3 ADVANCED OPERATION Page Page 3 INSTALLATION INSTRUCTIONS 3.1 INTRODUCTION 3.2 INITIAL INSPECTION 3.3 OPERATOR SAFETY INSTRUCTIONS CAUTION: When an instrument is brou 3.4 INSTALLATION Page Note: Switchin Page Page 3.5 OUTPUT CONNECTIONS Page 3.6 ACCEPTANCE TESTS Page Note: For meanin es" in the Reference Manual. of the hardware error numbers, refer to section 3.6.1 "Brief check" or to "Error Messa Page 4 GETTING FAMILIAR WITH THE POWER SUPPLY 4.1 INITIAL SETUP OF YOUR POWER SUPPLY Normal self test indications Self test errors Note: The address aa is the actual GPIB device address (default = 28). Note: The SELECT function is applicable only for multiple output models. 4.2 FRONT PANEL LAYOUT . 4 - 4 Users Manual + Gettin Familair with the Power Supply 4 - 5 1) The CALIBRATION mode is entered when you turn on the power supply while pressin the AUX key. 2) To unlock the keyboard, press the ENTER key for approximately 5 seconds. Note: The output channel indication is displayed only for multiple output channel models. 4.3 OUTPUT CHANNEL CONNECTIONS 4.4 GETTING STARTED le output model the number n will not be displayed. Page Note: The diameter of the jumper wire must be lar e enou h to carry the maximum short-circuit current. Page Page 5 USING YOUR PROGRAMMABLE POWER SUPPLY 5.1 INTRODUCTION 5.2 LOCAL OPERATION = applies to multiple output models only. Note: 5.3 REMOTE OPERATION 5.4 OPERATING FEATURES Page CAUTION: Only output channels with equivalent volta e and current ratin ed. s may be connected in series or in parallel to prevent that the channel with the lowest ratin s will be dama 5.5 HOW TO USE THE OPERATING FEATURES PM2811/12/13 ure 5.5.1 Output Channel Characteristics PM2831/32 ure 5.5.2 Output channel characteristics ure 5.5.3 Current sink characteristics . any chan ure 5.5.4 Volta e drop due to Wire Resistance R mode: Remote sensin ure 5.5.6 Connection of a Load in the Remote Sense Mode mode: ure 5.5.5 Connection of a Load in the Local Sense Mode Page ure 5.5.7 Power Output Crossover Point Page Page Page Local control (in CV or CC mode): Remote control (in CV or CC mode): Page Note: To remember which locations have been pro rammed and which have not, keep a record (such as the followin ) of which locations have been used. Local control (store/recall): Remote control (store/recall): Manual step function: Remark: When the next step is executed, the next volta e and current settin ): Page Remote control (automatic steppin ): External step functions Note: LOW = 0 to 0.8V and HIGH = 2 to 5V Tri gg er bus control: nored. Note: STEP pulses, received while the READY line is low, will be i 5.6 ADVANCED USE Note: For the PM2812 and PM2813 you can face a number of restrictions when connectin output channels in parallel to a load. Please read Appendix D to (outputs in parallel): with Two Outputs in Parallel CAUTION: To prevent noise pickup, twist the sense wires and shield them from the environment. ure 5.6.1 Local Sensin Page Page Page Page DT+ DT Remote sensin (loads in parallel): CAUTION: To prevent noise pickup, twist the sense wires and shield them from the environment. ure 5.6.6 Remote Sensin withTwo Loads in Parallel APPENDIX A ACCESSORIES A.1 Supplied with the instrument A.2 Optional Page APPENDIX B SCPI CONFORMANCE INFORMATION Page Page B.3 SCPI approved B.4 SCPI syntax and style Page APPENDIX C ABBREVIATIONS, SYMBOLS & TERMS C.1 Abbreviations Page Page Page C.2 Glossary of symbols C.3 Glossary of terms Page Page APPENDIX D APPLICATION FOR PM2812 AND PM2813 e mode. ure D.2 Channels connected in parallel to a load. Both channels are in Constant Volta e mode. Note: Coupled Protection is possible only for the channels in the same Power Supply. Try to prevent that the down pro Case 1: Constant Current Case 2: Constant Volta e, Output Current from a fixed minimum value to the maximum Case 3: Constant Volta e, Output Current from 0A to the maximum Page INDEX A C D E F G I L M N O P R S T V W