VoIP Applications
Configuration | Figure 9 shows the parameters configured for each PathBuilder S200 series switch. |
Voice | LAN | LAN | Voice |
Port | Port | Port | Port |
|
| IP Network |
|
Node 100 |
| PBX | |
Node 200 |
Node Record Nodename: Node100 Node Address: 100 Maximum Routing Hops:15 Maximum Routing Hops for Voice:2 Voice Switching Table Size: 16
Node Record Nodename: Node200 Node Address: 200 Maximum Routing Hops:15 Maximum Routing Hops for Voice:2 Voice Switching Table Size: 16
Voice Port Configuration
Port Number: 31
Port Type: Voice Interface Type:FXS Signalling Type: 1
E Lead Filter: Disable
Signalling Mode: Normal
Signalling Control: Immediate
PCM Mode: μlaw
Compression Rate: 8K
DSI Control: Enable
Smoothing Delay: 80 msec
Input Signal Level: 0dBm
Output Signal Level: 0dBm
Fax Support: Enable
Call Control: Switched
IP Interface Configuration Table Entry #: 1
Interface Number: 1
IP Address: 150.20.35.1
IP Address Mask: 255.255.255.0
Accept RIP: Enabled
|
|
|
|
|
|
|
|
|
| Voice Port Configuration |
|
| Ethernet Port Configuration |
|
|
|
| ||||||
|
|
|
| Port Number: 31 |
| ||||||
| (Configure for both nodes) |
|
|
|
| ||||||
|
|
|
| Port Type: Voice |
| ||||||
| Port Number: 4 |
|
|
|
| ||||||
|
|
|
| Interface Type: FXS |
| ||||||
| Port Type: ETH |
|
|
|
| ||||||
|
|
|
| Signalling Type: 1 |
| ||||||
| LAN Cable Type: AUI |
|
|
|
| ||||||
|
|
|
| E Lead Filter: Disable |
| ||||||
| Port MAC Address: |
|
|
|
| ||||||
|
|
|
| Signalling Mode: Normal |
| ||||||
| Transmit Queue Limit: 50 |
|
|
|
| ||||||
|
|
|
| Signalling Control: Immediate |
| ||||||
| Carrier Sense Filter:0 |
|
|
|
| ||||||
|
|
|
| PCM Mode: μlaw |
| ||||||
| Collision Detect Filter: 0 |
|
|
|
| ||||||
|
|
|
| Compression Rate: 8K |
| ||||||
| PB S200 Interface Number: 1 |
|
|
|
| ||||||
|
|
|
| DSI Control: Enable |
| ||||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Smoothing Delay: 80 msec |
|
|
|
|
|
|
|
|
|
|
| Input Signal Level: 0dBm |
|
|
|
|
|
|
|
|
|
|
| Output Signal Level: 0dBm |
|
|
|
|
|
|
|
|
|
|
| Fax Support: Enable |
|
|
|
|
|
|
|
|
|
|
| Call Control: Switched |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Configure PB S200 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
| Interface State |
|
|
|
|
|
|
|
|
|
|
| (Configure for both nodes) |
|
|
| IP Interface Configuration Table | ||||
|
|
| Interface #1 State: Enabled |
|
|
| Entry #: 1 | ||||
|
|
|
|
|
|
| Interface Number: 1 | ||||
|
|
|
|
|
|
| IP Address: 150.20.35.2 | ||||
|
|
|
|
|
|
| IP Address Mask: 255.255.255.0 | ||||
|
|
|
|
|
|
| Accept RIP: Enabled | ||||
|
|
|
|
|
|
|
|
|
|
|
|
Node 100
Route Selection Table
Entry # 1
Address: 200
#1 Destination: SOTCP
#1 Priority: 1
SoTCP Parameters (Configure for both nodes) TCP Port Number: 1099
Max. No. TCP Sessions: 10 Max. SVCs per session:1 Max. Total SVCs:10
Serial Connection establishment timeout: 100
TCP Connection establishment/clearing timeout: 200
TCP Keep alive timer: Disabled
Node 200
Route Selection Table
Entry # 1
Address: 100
#1 Destination: SOTCP
#1 Priority: 1
Node 100
SoTCP Map Table
Entry # 1
Destination X.25 Address: 200
Next hop IP Address: 150.20.35.2
Node 100
Voice Switching Table
RX DTMF Digits: 3W
No. of RX Digits: 3
Call Parameter 20031
Node 200
SoTCP Map Table
Entry # 1
Destination X.25 Address: 100
Next hop IP Address: 150.20.35.1
Node200
Voice Switching Table
RX DTMF Digits: 3W
No. of RX Digits: 3
Call Parameter 10031
Figure 9. Configurable Parameters to support VoIP
10 | Voice Over IP |