AD-1688
Weighing Data Logger
Instruction Manual
CANCEL | (+) |
© 2009 A&D Company, Limited. All rights reserved.
2. Unpacking
When unpacking, confirm that everything is contained.
•
•USB extension cable (0.5 m)
•
•
• | : |
• Instruction manual (this document) |
|
Cap
USB extension cable
•As power is supplied to the
Note: The
4. Key Operations
Key | When pressed | When pressed and held | |
(To press and | (To keep pressing | ||
| release immediately) | for 2 seconds or more) | |
SET | Displays the date and time. | Displays the function | |
|
| setting menus. | |
DISPLAY | Switches between the | Starts or stops data storage | |
(+) | display of data number and | at a set interval. | |
memory utilization rate. | (Only in the interval mode) | ||
| |||
CLEAR | None | Enters the data deletion |
2.Press the PRINT key of the weighing instrument to transmit the data to the
When the data is stored in the
3. Repeat step 2 as necessary.
4.When the number of data necessary is stored, disconnect the
The display of the
Note: During the data storage operation, do not remove the
5. Connect the
No part of this publication may be reproduced, transmitted, transcribed, or translated into any language in any form by any means without the written permission of A&D Company, Limited.
The contents of this manual and the specifications of the instrument covered by this manual are subject to change for improvement without notice.
1WMPD4001957B
Using the AD-1688
USB connector
Display
CANCEL | (+) |
with a
(CANCEL) | mode. |
5. Setting the Date/Time
Note: The date and time were set to the Japanese standard time at the factory when shipped. Before use, set the date and time to your local time.
Change the date and time as follows.
For easier setting, the
1. | Connect the |
| |
2. | Refer to “8.2. Date/Time Display” to display the date and time. |
| When the year, date or time is displayed, press and hold the |
When connected for the first time, a driver is installed automatically.
The
When operating this instrument, be sure to observe the following:
Caution
•Do not open the case to repair the
CANCEL (+)
B
When the
Each side has an opening. Use the openings as follows.
SET key for 2 seconds or more. The display flashes and the |
Using the following keys to set the date and time.
DISPLAY (+) key: Increase the value by one
CLEAR (CANCEL) key: Decrease the value by one
When the above keys are held pressed, the value is increased or decreased continuously.
6.Open the removable disk using Windows explorer. The data is stored in a file named
Precautions on Usage
Caution
CANCEL (+)
A: Attach a strap to carry.
B: Connect the cap and the main unit so that the cap will not be lost.
A
SET key: | Confirm the setting and go to the next item. |
3. After setting the year, month, day, hour and minute, press the |
SET key to return to the data number display. |
An example of the data opened using EXCEL is shown below.
•With the cap attached over the connectors, the
•The
1. Introduction
This manual describes how the
3.Features
•When connected to the
•The
•The maximum data to be stored is approximately 5000, using the A&D standard format (15 characters in 1 data set).
•The stored data can be read to a personal computer using USB. As the
•The data is stored in CSV format and can be used easily by software such as EXCEL.
6. Storing the Weighing Data |
6.1.Basic Operation
1.Connect the
Note: When the weighing instrument and a personal computer are connected simultaneously, communication with the computer has priority. Data storage will not be performed.
: Use the cable appropriate to |
| |
the | Weighing | |
the weighing instrument. | ||
instrument | ||
|
When the cable is connected, power is supplied to the
Note: ###### may appear in column B.
To display the date, broaden the column width.
7.After copied, delete the
Continued to the reverse side | |
|